a)
The rate of heat transfer to the air.
a)
Answer to Problem 142P
The rate of heat transfer to the air is
Explanation of Solution
Write the expression for the energy balance equation for closed system.
Here, rate of net energy transfer into the control volume is
Conclusion:
The rate of change in internal energy of the system is zero at the steady flow system.
Substitute 0 for
Here, mass flow rate is
The specific heat at constant pressure
Substitute
Thus, the rate of heat transfer to the air is
b)
The outlet temperature of the air.
b)
Answer to Problem 142P
The outlet temperature of the air is
Explanation of Solution
Write the expression to calculate the mass flow rate of air.
Here, volume flow rate of air at inlet is
Write the expression for the rate of heat transfer output.
Here, heat gained by the air is
Conclusion:
Substitute
Heat loss by the exhaust gases is equal to heat gained by the air.
Substitute
Thus, the outlet temperature of the air is
c)
The rate of entropy generation
c)
Answer to Problem 142P
The rate of entropy generation is
Explanation of Solution
Write the expression for the entropy balance in the heat exchanger.
Here, rate of net input entropy is
Conclusion:
Substitute
Here, mass flow rate at entry 1 is
Substitute
Thus, the rate of entropy generation is
Want to see more full solutions like this?
Chapter 7 Solutions
Thermodynamics: An Engineering Approach
- In large gas-turbine power plants, air is preheated by the exhaust gases in a heat exchanger called the regenerator before it enters the combustion chamber. Air enters the regenerator at 1 MPa and 550 K at a mass flow rate of 800 kg/min. Heat is transferred to the air at a rate of 2700 kJ/s. Exhaust gases enter the regenerator at 140 kPa and 800 K and leave at 130 kPa and 600 K. Treating the exhaust gases as air, determine the mass flow rate of exhaust gases.arrow_forwardAir (cp = 1.005 kJ/kg·°C) is to be preheated by hot exhaust gases in a crossflow heat exchanger before it enters the furnace. Air enters the heat exchanger at 95 kPa and 20°C at a rate of 1.6 m3 /s. The combustion gases (cp = 1.10 kJ/kg·°C) enter at 180°C at a rate of 2.2 kg/s and leave at 95°C. Determine the rate of entropy generation.arrow_forwardOutdoor air (cp = 1.005 kJ/kg·°C) is to be preheated by hot exhaust gases in a crossflow heat exchanger before it enters the furnace. Air enters the heat exchanger at 101 kPa and 30°C at a rate of 0.5 m3 /s. The combustion gases (cp = 1.10 kJ/kg·°C) enter at 350°C at a rate of 0.85 kg/s and leave at 260°C. Determine the rate of heat transfer to the air and the rate of exergy destruction in the heat exchanger.arrow_forward
- In large gas-turbine power plants, air is preheated by the exhaust gases in a heat exchanger called the regenerator before it enters the combustion chamber. Air enters the regenerator at 1 MPa and 550 K at a mass flow rate of 800 kg/min. Heat is transferred to the air at a rate of 2700 kJ/s. Exhaust gases enter the regenerator at 140 kPa and 800 K and leave at 130 kPa and 600 K. Treating the exhaust gases as air, determine the exit temperature of the air.arrow_forward5-84 Air (Cp=1.005 kJ/kg°C) is to be preheated by hot exhaust gases in a cross-flow heat exchanger before it enters the furnace. Air enters the heat exchanger at 95 kPa and 20°Ct at rate of 0.6 m³/s. The combustion gases (Cp=1.10 kJ/kg°C) that enter at 160°C at a rate of 0.95 kg/s and leave at 95°C. Determine the rate of heat transfer to the air and its outlet temperature. Air 95 kPa 20°C 0.6 m³/s Exhaust gases 0.95 kg/s 95°Carrow_forwardFeedwater heaters are used to increase the efficiency of steam power plants. A particular heater is used to preheat 10 kg/s of boiler feed water from 20° C to 188° C at a pressure of 1200 kPa by mixing it with saturated steam bled from a turbine at 1200 kPa and 188° C. Although insulated, the heater loses heat at the rate of 50 j per gram of exiting mixture. What fraction of the exit stream is steam?arrow_forward
- Hot combustion gases enter the nozzle of a turbojet engine at 350 kPa, 1007 0C, and 95 m/s, and they exit at a pressure of 100 kPa. Assuming an isentropic efficiency of 95 percent and treating the combustion gases as air determine a- The exit velocity b- The exit temperaturearrow_forwardHot air at 400°C and 150 kPa is to be used to produce saturated steam at 200°C in an insulated, non-mixing heat exchanger. Water enters the heat exchanger at 20°C while the air leaves at 350°C. The mass flow rate of air is 0.8 kg/s, pressure drops are negligible, and specific heats for air are evaluated at the average air temperature.What is the mass flow rate of water, in kg/s. Report your answer to four decimal places using rounding.arrow_forwardHot combustion gases enter the nozzle of a turbojet engine at 250 kPa, 650°C, and 70 m/s and exit at 80 kPa and 420°C. The mass flow rate is 1.2 kg/s. Assume the heat losses to the surroundings is 90kW and the surroundings is at 27°C. Determine (a) the exit velocity and (b) the decrease in the exergy of the gases. Take k = 1.3 and c, = 1.15 kJkg-°C for the combustion gases. Qtoss = 90kW 250 kPa Combustion gases 80 kPa 650°C 420°C 70 m/s m = 1.2 kg/s m = 1.2 kg/sarrow_forward
- Hot exhaust gases leaving an internal combustion engine at 400°C and 150 kPa at a rate of 0.8 kg/s are to be used to produce saturated steam at 200°C in an insulated heat exchanger. Water enters the heat exchanger at the ambient temperature of 20°C, and the exhaust gases leave the heat exchanger at 350°C. Determine the rate of exergy destruction in the heat exchanger.arrow_forwardConsider an aircraft powered by a turbojet engine that has a pressure ratio of 12. The aircraft is stationary on the ground, held in position by its brakes. The ambient air is at 27 deg.C and 95 kPa and enters the engine at a rate of 10 kg/s. The jet fuel has a heating value of 42,700 kJ/kg, and it is burned completely at a rate of 0.2 kg/s. Neglecting the effect of the diffuser and disregarding the slight increase in mass at the engine exit as well as the inefficiencies of engine components, determine the force that must be applied on the brakes to hold the plane stationary.arrow_forwardIn a gas turbine the compressor takes in air at a temperature of 15°C and compresses it to four times the initial pressure with an isentropic efficiency of 82%. The air is then passes through a heat exchanger heated by the turbine exhaust before reaching the combustion chamber. In the heat exchanger 78% of the available heat is given to the air. The maximum temperature after constant pressure combustion is 600°C, and the efficiency of the turbine is 70%. Neglecting all losses except those mentioned, and assuming the working fluid throughout the cycle to have the characteristic of air find the efficiency of the cycle. Assume R-0.287 kJ/kg K. and y - 1.4 for air and constant specific heats throughout 11.77. wnet. 29.2 Kg/ kg.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY