The amplification factor and transconductance in a triode are 60 and 30 millimhos respectively. With constant grid voltage, find the change in the anode current (in mA) when the anode voltage is changed from 5 V to 20 V.

Q: Given a unity feedback system with forward transfer function G(s) = K* (s+z)/((s+1)* (s+7)).…

A:

Q: What size ungrounded conductors do we need for the 60 amp load? All conductors have typeTHHN…

A: THNN wire is high heat resistance wire that can withstand the heat upto 90°C. The insulation in THNN…

Q: Problem 2: Use Superposition to find the voltage across the 8-Ohm resistor. 40 V + 2 Ω + 8 ΩΣυ 6Ω…

A:

Q: Time domain system models: Plot signals and final convolution of x(t)*g(t)

A: Given: Signals x(t) and g(t) as,  x(t)=2[u(t)-u(t-2)],g(t)=(2-t)[u(t)-u(t-2)], To do: a) Plot x(t),…

Q: What Is Tripping My Circuit Breaker?

A: Circuit breaker: It is an electric safety device, which can interrupt the electric current flow when…

Q: (2) In the circuit shown below, V₁-4v, V3-3v. Find V₂. (Hint, the voltage on the wire at the top is…

A: Apply KVL in a loop KVL states that the algebraic sum of voltages in a closed loop is zero.

Q: √7eπi = find the rectangular form

A: Note: eix=cos x +i sin xe-ix=cos x -i sinx

Q: Why do we use starter for a DC motor?

A:

Q: Example 1. Determine the output waveform for the sinusoidal input of Figure 3. 0 20 V 72 T o Vi V=5…

A:

Q: The op amp in the noninverting summing amplifier of (Figure 1) is ideal. Consider vo = 4va + 3vb +…

A:

Q: Design a length M = 6 FIR filter with real coefficients so that the filter's frequency response H(w)…

A:

Q: Draw the output voltage waveform of the circuit shown and label the values.

A: The given circuit is a series clipper with a DC supply. The circuit can be analysed based on the…

Q: For the circuit given below, find the Thèvenin equivalent at terminals a- b, where R = 6 . Please…

A:

Q: If the inset image was created by linearly scaling from DN = 0 to 100 instead of DN = 50 to 100, the…

A: Note: DN (Digital Number) describes the intensity of each pixel of an image If DN is more,…

Q: 6. Given the following circuit, determine VA (no load) and VA & PT with 10k load connected to Output…

A: In this question we need to find the voltage at output A at no load and with 20 Kohm load as shown…

Q: 12 V M 4Ω ΑΛΛ 4Α 3Ω M 10 Ω 2Ω M 5Ω ( 24

A:

Q: Find the equivalent resistance between X and Y. 552 X- 1092 ww 252 252 252 www 1092

A:

Q: Example 4. Repeat Example 3 using Silicon diode.

A: Given: And the diode is of silicon.  To find: Output voltage waveform.

Q: The Fourier Sine transform of f(x) Fs [f](z) = The Fourier Cosine transform of f(x) Fc[f](z) = f(x)…

A:

Q: Given you have a working DC motor drive circuit, we want to give the user more contro over it…

A: DC motor drive circuit : Motor Driver circuits are current amplifiers. They act as a bridge between…

Q: For the following truth table, derive the standard SOP and standard POS expressions. U OOH OOLLLLL…

A: We need to find out the SOP and POS form for given truth table .

Q: 2. Consider now the following circuit: 1 ΚΩ M 12 V + 300 Ω M + Vo I 1 ΚΩ M 5 V + 1 ΚΩ w ↑ 10 mA (a)…

A:

Q: For the circuit given below, where V = 14 V, what resistor connected across terminals a-b will…

A:

Q: Calculate Ix1 the component of Ix due to the voltage source 10V alone.  2.

A:

Q: e. Determine Ix using delta to wye ransformation. +1001 55 n ३08 4.0 in XI T > vol v9: M 5.5

A:

Q: QUESTION 4 Which is these is the BEST description of what the SCALING command does in a PLC? Allows…

A: The BEST description of what the SCALING command does in a PLC is: A) Allows the programmer to set…

Q: 7. If I now attach a load resistor of 5k across the terminals, what is the current through the load…

A: Given: with load resistance, RL=5kΩ, To find: Current through load resistance.

Q: What is a thick film resistor ? list some applications where it used and how it is used.

A: We need to tell about thick film resistor.

Q: 15.32 A separately excited dc generator has the magnetization curve shown in Fig. P15.32. Given that…

A:

Q: Briefly explain how does the given Lown wave circuit defibrillator work? Power Step-up transformer R…

A: Defibrillator: It is nothing but an electronic High voltage discharging device which is helpful in…

Q: the following Assuming D1 is ON and D2 is OFF, with Vs1 = 14.4 V, Vs2 = 1.3 V, R₁ = 1.9 kN, R₂ = 6.1…

A:

Q: For all circuits assume an ideal op-amp: 1) For the inverting amplifier shown, calculate a) Vout/Vin…

A:

Q: Draw the output voltage waveform. Identify the function of the circuit.

A: The given circuit is a biased clamper circuit. The clamper circuit will shift the waveform to a…

Q: 50Ω W b 3.02 d 250 3.50 4Ω W M 6Ω M 532 50 M C ΖΩ 2.22 e 100Ω W 75.223 -f

A: Given an electrical circuit. To find the resistance across the terminals b and e.

Q: It is the general practice to have the high voltage side lead the low voltage side by the above…

A: The high voltage and low voltage winding terminals of a three phase transformer are connected either…

Q: Given A=-4ax + 2ay + 3az and B=3ax + 4ay - az, Find (a) the magnitude of 5A - 2B; (b) a unit vector…

A: Since you have posted a question with multiple subparts, we will provide the solution only to the…

Q: The synchronous speed and the percentage slip of an AC motor are 900 rpm and 3 percent respectively.…

A:

Q: Find the transfer function G(s)=X₂(s)/F(s) in the network below: 1 N-s/m 1 N/m oooo 1 kg 1…

A:

Q: Use the figure to design a problem that helps other students to better understand nodal analysis.

A: Every electrical network may be solved using nodal analysis, which is what it is called. the formula…

Q: A system is described by where and ₁ (0) = x(t) = Ax(t) 0 1 ^-[44] A = -2 -3 1 and 2 (0) = 0.…

A:

Q: Q4. A device has the v-i characteristic shown in Figa) below.

A: According to the question, for the given diagram, and output characteristics of JFET as shown below,…

Q: ): Find the quantity of charge if the current equation is i(t) = 8t² + t, in the interval between 1…

A:

Q: A certain voltage doubler has 20 V rms on its input. What is the output voltage? Draw the circuit,…

A: Given, Input RMS voltage = 20 A voltage doubler is a type of voltage multiplier in which the output…

Q: Consider a circuit shown in the figure. Ignore the internal resistances of the batteries. ℰ1 = 48 V…

A: It is given that: ε1=48 V ε2=26 VR1=7 ΩR2=4 ΩR3=4 Ω.

Q: + is ( 1 ) 10 ΩΣ |υ 6023 40 μΗ 1 μF Click to see additional instructions The sinusoidal current…

A: Given that IS = 3 cos (200000t) A C =1 micro farad L = 40 micro Henry R1 = 6 ohm, R2 =10 ohms

Q: Find the overall transfer function R G₁ G₁ G₂ H₂ H₂ G₁ Figue

A:

Q: 12.26 A 2-mH coil in a tuning circuit has its resonance at 460 kHz. What is its inductive reactance…

A: Given  Inductance = L = 2 mH Frequency = F = 460 kHz

Q: Consider the following circuit. The frequency of oscillation is:

A: The given circuit is a Colpitts oscillator and the frequency of oscillation is based on the feedback…

Q: A radar system operates at 6 GHz 3 MW power output. If the antenna diameter is 5m and the receiver…

A:

Q: x(t) = e¯atu(t) (a > 0) h(t) = u(t)

A:

Photoconductive Cell

Photoconductive cells are light-sensitive resistors in which resistance is inversely proportionated to light intensity when illuminated. These devices consist of a thin single-crystal or polycrystalline film of composite semiconductor materials. Cadmium sulfide (CdS) is used to make the most commercially available photoconductive particles which are sensitive to light in the visible spectrum. Other less commonly used substances respond to infrared light, but not to the visible spectrum. Such substances are lead sulfide (PbS), lead selenide (PbSe), and lead telluride (PbTe), and so on.