Final (a) b) 41 (1) ADC shunt motor is rated 10HP, 250V and is connected to 235V source. The armature resistance is 0.2 ohm, the field circuit resistance is 125 ohm and the total rotational losses are 380W. The motor is driving a load, and it draws an armature current of 30A. Calculate the output power. 6490 6870 7492 7460 Boş birak

Final (a) b) 41 (1) ADC shunt motor is rated 10HP, 250V and is connected to 235V source. The armature resistance is 0.2 ohm, the field circuit resistance is 125 ohm and the total rotational losses are 380W. The motor is driving a load, and it draws an armature current of 30A. Calculate the output power. 6490 6870 7492 7460 Boş birak

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights.
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights. design the single-phase, full-wave, ac/ dc converter. show design specifications, the reason for DC motor selection. correct manual circuit, and correct automatic closed-loop control circuit
L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
A 220 V DC series motor runs drawing a current of 30 A from the supply. Armature and field circuit resistances are 0.4 and 0.1 respectively. The load torque varies as the square of the speed. The flux in the motor may be taken as being proportional to the armature current. To reduce the speed of the motor by 50% the resistance in ohms that should be added in series with the armature is
Speed control of a 140 V, 1.68 kW DC motor single phase thyristor full wave AC-DC It is made by the converter. AA supply voltage 220 V (rms) Is 50. In the converter It is assumed that there is no loss. The armature resistance of the DC motor is = 0.417 Q. Very a large inductance is connected in series with the motor. The motor voltage constant is = 0.0964 V/rpm. The motor can be considered as a permanent magnet DC. According to this, a) Draw the driver (converter-motor) power circuit. b) Calculate the nominal current of the motor. c) Supply voltage, supply current, converter output voltage for ignition angle a = 30 ° and Draw the waveforms for the converter output current. d) = 950 rpm and for nominal current, d1) The firing angle of the converter, d2) Effective value of supply and thyristor current, d3) Supply power factor, calculate.
• Q5/ in a DC motor. List and describe the types of losses that occur
A 250 V series motor has an armature resistance of 0.2 ohm and a series-fieldresistance of 0.18 ohm. If the speed is 6oo RPM when the current is 32 amps.What will be the motor speed when the load is reduced so that the current is18 amps, under which condition the percent flux change is 50 % of the percentcurrent change.
The current drawn by 220 V dc shunt motor of armature resistance 0.5 ohm and back emf 200 V is
8. A dc series motor develops a torque of 20 Nm at 3 A of load current. If the current is increased to 6A, the torque developed will be (a) 10 Nm (b) 20 Nm (c) 80 Nm (d) 40 Nm
A series motor runs at 800 rev/min when the voltage is 400V and the current is 25A. The armature resistance is 0.4 ohm and the series field resistance is 0.2 ohm. Determine the resistance to be connected in series to reduce the speed to 600 rev/min with the same current.
A DC chopper is used in regenerative breaking mode of a dc series motor. The dc supply is 600 V, the duty cycle is 70%. The average value of armature current is 100 A. It is continous and ripple free. What is the value of power feedback to the supply ?
Reducing the supply voltage so that Vnew = Vold / V3 reduces the maximum torque of the motor so that Tmaxnew= ...Tmaxold . * .... ...