Explain why are most marine piles circular in cross section?
Q: State the outcome of driving a displacement pile into a loose sand and plastic clay?
A: The outcome of driving a displacement pile into a loose sand and plastic clay are listed below:
Q: Explain the properties of Pile caps ?
A: Answer Introduction A pile cap is a thick RCC slab that is laid on the timber or concrete piles. The…
Q: Explain the difference between short piles and long piles.
A: Short pile : - Short pile are generally 2m to 4m and from 250 mm to 350mm diameter. - The piles may…
Q: Why would it be inappropriate to use the Terzaghi bearing capacity formulas to determine the toe…
A: The ultimate load which a foundation can support is calculated by terzaghi bearing capacity…
Q: Describe the important advantages of driven piles.
A: Piles are defined as a foundation that provides support for the building structure. it is used for…
Q: Q-(e) If the effective plan area of a warehouse is 54 sq. m, and maximum height of piles permitted…
A: Given data- Effective plan area=54 m2maximum height of piles=270 cm=2.7 mTo find-The number of bags…
Q: Q # 1. What is pile foundation? Discuss the classification of pile based on materials/composition…
A: Pile foundation- a foundation laid with deep pile is known as pile foundation.
Q: What are the two methods that are used to determine the capacity developed along the length of the…
A: Pile load capacity depends on a number of factors including cross section, pile length and shape…
Q: Explain why pile driving formulas are not reliable, and why a wave equation analysis is a better…
A: Solution: Pile driving formulas are not reliable because Pile Driving formulas are very simple.…
Q: How does the Pile capacity can be determined?
A: Piles may either be pushed or casted on the spot. Pile drive is accomplished through: affect lateral…
Q: Explain some conditions which are consider for the structural design of driven piles.
A: The driven pile may be a form of pile that inserted up to the exhausting layer within the soil…
Q: Describe the categories of the structural loads applied to piles.
A: pile is the long cylindrical member made up with material which having high compressive strength .…
Q: Explain some factors which are consider for the design criteria of wood piles.
A: Wood piles are to be coated special Chemicals like creosote oils so that the wood pipe is resistant…
Q: Describe the Arrangement for Piles in a Group.
A: If applied load is large and then pile group is used rather than an individual pile. The individual…
Q: Explain the symbols used for Pile Groups ?
A: Piles are vertical or slightly inclined, relatively slender structural foundation members. They…
Q: Why does the soil between individual piles may become “locked-in”?
A: The consolidation and compaction of soil beneath the piles is due to the soil between the individual…
Q: Explain the methods of determining load carrying capacity of a pile.
A: Methods of determining load carrying capacity of a pile: Static method : suitable for friction…
Q: Define the functions of cap block, drive cap and pile cushion in driven piles?
A: Solution: Cap Block are generally installed between the end of hammer and the drive cap to control…
Q: Should engineers rely solely on Hiley’s formula in the design of H-piles?
A: Hiley Pile driving formulae: Hiley's pile-driving formula is described below according to IS:2911.…
Q: Why there is need of pressure piles?
A: Answer Pressure pile used in the foundation engineering under following condition given in step 2
Q: What distinguishes displacement piles from nondisplacement piles?
A: When the depth of a base exceeds three times the width, it is said to be stacked. A powered pile is…
Q: What is the ultimate downward load carrying capacity of a single pile driven in soil?
A: The ultimate downward load carrying capacity of single pile driven in soil are : - Using Analytic…
Q: Explain the role of geotechnical engineers in pile construction.
A: A geotechnical engineer tests the soil for various aspects of physical and index properties. The…
Q: Explain these two questions based on pile foundations in about 8-10 lines. i) How do the soil…
A: A Pile foundation is a deep foundation whose height is more than the breadth of the foundation. It…
Q: Question- If the effective plan area of a warehouse is 54 sq m, and maximum height of piles…
A: given- Area of warehouse-A=54 m2maximum height of piles=270 cm
Q: As driven piles penetrate into a saturated clay soil, why the material in the vicinity of the pile…
A: Once a pile is driven into clay, the soil around the pile develops vertical and horizontal…
Q: What are Compression piles ? Explain the purpose & uses of Compression piles ?
A: Compression Pile :These are the piles that are acted upon by compression loads and they carry the…
Q: Explain about Seismic Consideration in pile design ?
A: All objects, including builds, have a natural or fundamental period at which they vibrate if jolted…
Q: In designing the lateral resistance of piles, should engineers only use the earth pressure against…
A: Answer Introduction Lateral load resisted by the following ways 1) Passive soil resistance on the…
Q: What are the methods of increasing the lateral resistance in piles.
A: The resistance caused on piles due to lateral load is known as lateral resistance. It is the sum of…
Q: 1. What types of piles you know by their bearing mechanism
A: The various types of piles are: Sheet piles: This type of pile is mostly used to provide lateral…
Q: Discuss about the Carrying capacity of single pile in granular and cohesive soil ?
A: The load bearing capacity of foundation soil or rock which enables it to bear and transmit load…
Q: Explain the design process of pile supported mats.
A: Question is based on the pile supported mat . In the question design process of mat foundation…
Q: Provide the list of different pile driving hammers.
A: The different pile driving hammers are:
Q: Explain these two questions based on pile foundations: i) How do the soil stress states and strain…
A: 1) How do the soil stress states and strain states change by the installation and structural loads?…
Q: Describe the factors of safety for design of piles.
A: Answer IntroductionA pile foundation is a cylindrical structural member made of concrete, steel, and…
Q: Define the types of piles on the basis of their function with sketches.
A: Answer:- Pile: A pile is a long cylinder made up of a strong material such as concrete and a series…
Q: For a rigid pile cap with vertical piles at the middle and raking piles at the sides,what is the…
A: Brief concept- Piles are provided in the deep foundation where the applied load is very high and the…
Q: What the advantages Left-in casings for mini-piles have ?
A: There are mainly two reasons to account for designing mini-piles as friction piles: (i) Due to its…
Q: What are the primary advantages of using laterally loaded vertical piles instead of battered piles?
A: Introduction: Piles are used generally to transmit vertical loads and lateral loads to the…
Q: Structural designers commonly mention that steel piles are a good choice for sites where long piles…
A: Steel pile and concrete pile don't seem to be interchangeable solutions for foundation repair. every…
Q: Compare features of cast in place piles: a) Constructed by a driven steel shell with concrete b)…
A: Cast in-situ pile:Cast-in-place (Cast-in-situ) piles are those piles that are cast in position…
Q: What s pile foundation? Discuss the classification of pile ba =/composition and load transfer…
A: Pile foundation- Plie foundation is a type of Deep foundation where depth of foundation is grater…
Q: What are the main components in typically pile driving equipment?
A: There are various equipment for driving of pile in the ground. All of them have some component that…
Q: Elevati Distanc on (ft) (y- axis) e (ft) (x- axis) 5 15 10 17 10 18 15 19 15 28 33 40 -5 44 -5 54…
A: First find the excavation volume using the give values and then determine the volume of filling.…
Q: Compare circular, square and I section piles in terms of usage, cost and advantages/disadvantages?
A: Circular Piles Usage These sections require less material to construct and provide stronger and…
Q: What is “block failure” in a group of piles and how does it differ from individual failure?
A: The cylinder which is long and used for carrying loads and transfer it to hard strata and made up of…
Q: Briefly explain the types of failures in pile groups.
A: Pile foundations are among the most common alternatives for heavy-duty constructions and those with…
Explain why are most marine piles circular in cross section?
Step by step
Solved in 2 steps