Consider the circuit diagram below. The circuit supplies power to the unknown resistive load, L. Determine the Thevenin equivalent circuit for the supply circuit. Verify that your Thevenin equivalent is indeed equivalent to the original circuit by simulating both circuits using CircuitJS and reporting the load current in each. Attach an exported image or screen shot of both of your circuits from CircuitJS with the current and voltage “shown” (colors are shown on the diagram).

Consider the circuit diagram below. The circuit supplies power to the unknown resistive load, L. Determine the Thevenin equivalent circuit for the supply circuit. Verify that your Thevenin equivalent is indeed equivalent to the original circuit by simulating both circuits using CircuitJS and reporting the load current in each. Attach an exported image or screen shot of both of your circuits from CircuitJS with the current and voltage “shown” (colors are shown on the diagram).

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 1RQ: 1. What is the dielectric?

See similar textbooks

Similar questions

Find T 0.5 ms 40 92 www www 892 160 92 20 mH www
10 نقاط :choose the correct value of the current passing throw -j100 40+j50 -j100 60 0.262- 15 0.147443.43 B O 5.854445.83 A ww 007s7
Band 1 GR R y BU G GR BN G Band 2 R W V V GR BU R GR W BU Band 3 BN R BL S R R BL GO BL R Table 1 Resistor Color Codes and Measurements Band 4 GO 60 GO GO GO GO GO GO GO GO Band 5 Theoretical value R Plus Tolerance 8205% 8612 3 900±5% 40952 3705 27 2±5% 28-35 25-65 0.47±5% 0-493552 0.44651 71402 6800 ± 5% 5600 55880 82nt 5% 1-82±5% 86-1-22 1.892 R Minus Tolerance 39 150 40.952 56001 ± 540 5880 Measured Value 7792 8012 38542 26 0.45 6460 6630 53201 5570 77-92 80.5 #1.712 37.05~ 5320 2 1.82 39.25 5520 MAKE A CONCLUSION FOR THIS (8 SENTENCES ONLY) The content must be the connection of resistor color codes to tolerances and the relationship of the measured value to the theoretrical value
Useful constants: k=9.00×109 N.m2/C2 ε0= 8.85×10-12 C2/N.m2 µ0=4π×10-7 T.m/A mp=1.67×10-27 kg me=9.11×10-31 kg e=1.6×10-19 C g=10.0 m/s2
Oscilloscope-XSC1 MAAA Channel B 643.751 mV 643.751 mV 0.000 V T1 T2 T2-T1 Time 379.198 ms 379.198 ms 0.000 s Timebase Scale: 500 us/Div X pos.(Div): 0 Y/T Add B/A A/B Discussion Channel A 1.086 V 1.086 V 0.000 V Channel A Scale: 1 V/Div Y pos.(Div): 0 AC 0 DC ● Channel B Scale: 1 V/Div Y pos.(Div): 0 AC 0 DC Reverse Save Trigger Ext. trigger Edge: fz B Ext Level: 0 V Single Normal Auto None ZA X Fig(6): The input and output waveforms for differentiator Operational Amplifier 1- If Op Amp is operating at 1000 Hz as input wave, what is the frequency of the output signal? 2- Why do we use Spike function? List the possible application of spike waveform.
* For a clamper circuit, if the input is the blue waveform and the output is the red one. Scale 5V/Div. Determine the correct operation circuit XPG1 MA S a 1 C1 10μF XFC1 AVAFE HH D1 1N4001 VI 5V 3 R1 $10k C1 10μF XFG1 50 2 D1 1N4001* V1 6V C1 10μF D1 1N4001 V1 10V R1 Σ10kΩ R1 >10K 3 O 1 O 2
VIN = 10V; R = 25KQ. Determine lo1 (in mA)? Soi R 9 ke I ka Select one: a. 7.02 b. 10.0 C. -25 d. +25 e. 6.5
Inductive Circuits Fill in all the missing values. Refer to the following formulas: XL=2fLL=XL2ff=XL2L Inductance (H) Frequency (Hz) Inductive Reactance ( ) 1.2 60 0.085 213.628 1000 4712.389 0.65 600 3.6 678.584 25 411.459 0.5 60 0.85 6408.849 20 201.062 0.45 400 4.8 2412.743 1000 40.841
1. What is the dielectric?
ANGLE 30° 60° 90° 90/38cm 90/38cm 90/76cm 90/114cm 90/152cm 90/185cm 90°/215 SHADING % 10% 50% 100% 0% 10% 20% 30% 50% 80% 100% IRRADIATION 45.79 34.70 52.79 86.96 85.56 107.1 107.3 46.02 65.26 99.76 VOLTAGE 19.21 19.53 19.19 19.52 19.14 19.11 19.27 19.42 19.53 19.65 AMPERE 0.015 0.017 0.016 0.021 0.022 0.022 0.022 0.022 0.024 0.024 POWER 0.288 0.346 0.323 0.411 0.432 0.426 0.426 0.444 0.484 0.471 In table. At what percentage of shade that current, voltage and power reach the minimum a. output? Explain your answer? b. In table. Record the result of this shading effect on the output of a solar module? c. In your own conclusion, in table. What is the effect of shading to the efficiency of the performance of the PV cell with regards to Voltage, Current and Power? Explain
Discussion For the circuit below complete the table R 5Ω 10 V 60 Hz 100 μF R Total 10+j0 Volts 10 Z0° 68.623m +j364.06m Amps 370.5m Z 79.325° 5+ j0 0- j26.5258 5 - j26.5258 Ohms 520° 26.5258 -90° 26.993 Z-79.325°
Find the value of (vo? 3 mV O 06V © day σαν ODAV 1 4 ΚΩ Μ th 100 501 20 ΚΩ o+ s° 10 %