A corporation has a medium with a 7 MHz bandwidth (lowpass). The corporation needs to create 9 separate independent channels each capable of sending at least 12 Mbps. The company has decided to use QAM technology. What is the minimum number of bits per baud for each channel? What is the number of points in the constellation diagram for each channel? Let d = 0

A corporation has a medium with a 7 MHz bandwidth (lowpass). The corporation needs to create 9 separate independent channels each capable of sending at least 12 Mbps. The company has decided to use QAM technology. What is the minimum number of bits per baud for each channel? What is the number of points in the constellation diagram for each channel? Let d = 0

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 27VE

See similar textbooks

Similar questions

Suppose, you have 6 voice channels, each of 60MBPS. You have to use synchronous TDM to multiplex these channels. If 2 characters at a time are multiplexed (2 characters in each output slot), answer the following: What is the size of an output frame in bits? What is the output frame rate? What is the duration of an output frame? What is the output data rate? Input bit duration? Output bit duration? Output slot duration?
We need to use Synchronous Time Division Multiplexing to combine 17 different channels, where 10 channels are each of 300 Kbps and 7 channels are each of 600 Kbps. A unit is 1 bit. Now, answer the following questions using multilevel TDM with no synchronization bit. Your answers must have units. i) What is the output frame duration? ii) What is the output frame rate? iii) What is the output bit rate?
A line has a signal-to-noise ratio of 1000 and a bandwidth of 4000 kHz. What is the maximum data rate supported by this line? If the bandwidth of the channel is 5 kbps, how long does it take to send a frame of 100,000 bits out of this device? What is the maximum data rate of a channel with a bandwidth of 200 kHz if we use four levels of digital signaling?
We need to use Synchronous Time Division Multiplexing to combine 17 different channels, where 10 channels are each of 300 Kbps and 7 channels are each of 600 Kbps. A unit is 1 bit. Now, answer the following questions using multilevel TDM with no synchronization bit. Your answers must have units. i) What is the output bit duration? ii) What is the size of an output frame in bits? iii) What is the input bit duration?
Consider a communication channel with bandwidth B = 8000 Hz. Suppose the channel has a signal-to-noise ratio S/N = 541. What is the maximum data rate of this channel? ? What is the minimum number of signal levels needed to achieve a data rate of 64000 bps?
Suppose there is a b+n (Sum of first and last digit of your Reg#) Mbps microwave link between a geostationary satellite and its base station on Earth. Every minute the satellite takes a digital photo and sends it to the base station. Assume a propagation speed of 2.4*108 meters/sec. 1. What is the propagation delay of the link? 2. What is the bandwidth-delay product?
Your company has a video transcoder. Each network interface returns the number of transmitted and received octets at a precise moment. The bitrates need to be added to the transcoder. Calculate the needed bitrates for receiving (Rx) and transmitting (Tx) considering a pooling rate of 4Hz. Tx: 289652580 Rx: 6488574452
Consider a geostationary satellite-based system. Earth stations are multiplexing digital information streams and they transmit them to the satellite. Due to the very long distance of the satellite is from the surface of Earth, you wish your earth station transmitters and the satellite transmitter to operate their amplifier at its maximum power output level. If you were the designer of the system, would you select to use Frequency Division Multiplexing (FDM) or Time Division Multiplexing (TDM)?
We need to transmit 100 digitized voice channels using a pass-band channel of 20 KHz. What should be the ratio of bits/Hz if we use no guard band?
For data is transmitted over twisted-pair cable, you have these characteristics: A signal's power on the channel is 60 dB, signal attenuation is 2 dB per 100 meters, and average noise power on the cable is 0.15 dB per meter. Answer the following questions: What's the S/N ratio at the end of a 60-meter channel? What's the S/N ratio at the end of a 1.5-kilometer channel? What's the maximum channel length if the receiving device requires at least 25 dB of S/N ratio for reliable operation?
3. Draw the QAM analog signal that transmits the following bit stream: 0 10 1001 0 10 0 1 1 0 1 11 1 0 1 0 Assuming that the current analog signal is represented as y = sin t. You need to draw one complete cycle for each modulation change. You can assume that the number of amplitude level is 2 and the number of phase level is 4. You may use the mapping table we used in our lecture to represent data bits.
Assume that, in a Stop-and-Wait system, the length of the line is 10 Km, the volume of the pipe is 5Kbytes, and 1 bit takes 40 milliseconds to make a round trip. What is the bandwidth of the line?