8. = 5º, A chopper feeding on RL load is shown in Fig.2 With V=200 V, R-502, L = 5 mH, | f=1 kHz, d-0,5 and E-0 V. Calculate: (a) Maximum and minimum values of load current (b) Average value of load current (c) RMS load current RI (d) Effective input resistance as seen by source (e) RMS chopper current. Chopper FWD Fig. 2 gegee w L E V 1

8. = 5º, A chopper feeding on RL load is shown in Fig.2 With V=200 V, R-502, L = 5 mH, | f=1 kHz, d-0,5 and E-0 V. Calculate: (a) Maximum and minimum values of load current (b) Average value of load current (c) RMS load current RI (d) Effective input resistance as seen by source (e) RMS chopper current. Chopper FWD Fig. 2 gegee w L E V 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

When comparing values for shape factor: a. A value of 0.707 is ideal b. There is no ideal value c. A value of 1.414 dB is ideal d. A value of 1.0 is deal
A three phase full controlled converter is supplied by a phase voltage Vs=120V, 60 Hz. Consider a resistive load R=10 Q. If the average value of the output current is equal to 7.025A and the RMS value of the input line current is equal to 8.93A, then the TUF would be equal to: Select one: a. 0.955 O b. 0.557 O c. 0.153 O d. 0.707
24. A step up chopper has load voltage of 600V and is sup- plied from a constant de source of 150V. If the OFF time of the chopper is 40 µs and desired output voltage is 300V find ON time of the chopper? (A) 5 µsec (C) 30 µsec (B) 10 μsec (D) 40 µsec
r:09 A moodle1.du.edu.om An application demands that sinusoidal pressure variation of 250 Hz be measured with no more than 2% dynamic error. In selecting a suitable pressure transducer from vendor catalog, you note that a desirable line of transducer has a fixed natural frequency of 500 Hz but that you have a choice of transducer damping ratio of between 0.5 and 1.5 in increments of 0.05. select a suitable transducer. The value of damping ratio is between the following values Select one: O a. 0.707 and 0.807 O b. 0.631 and 0.692 O c. 0.2356 and 0.5625 O d. 0.5215 and 0.5625 Previous page Next page 1 Aşsignmen
The circuit is shown below, Vin is the sinusoidal waveform with magnitude 5V and frequency is 100 Hz, R = 1 k, C = 1 uE, the chip is supplied by + 12 V source. a) What is the waveform of Yout? b) Calculate the magnitude of Vo c) If Vin is triangle waveform, what is the output waveform? -Vout , if Vin is triangle waveform with magnitude of 5 V (peak-to-peak value is 10 V) and frequency is 10 kHz, calculate waveform of you and the magnitude of I/?
7) Two loads ere connected in parallel to bn e-c source and tako currents of 10 and 40 cmp, respoctively. If thu sinusoiarl weves of the componentcurrents are out of phese by 30 elec dog,' calculate the resultant curront. Ans. 48,7. amp.
The underlying objective of power factor correction is to reduce the drawn by the load. (A) current (B) reactive power active power D current and reactive power (E current and active power
Frequency Control Question 3: If the regulation R = 1% and damping coefficient D = 0.8, the change in generation of the area for a drop in frequency of 0.0015 p.u. in p.u. is
We examined the common source amplifier shown in the figure in the 5th experiment. The selection criterion of the input capacitance is Xcin = 0.1Rin: Calculate the required input capacitance value, Cin , if an input signal with a frequency of 2 kHz is applied. Şekitde gösterilen ortak source yükseltecini 5. deneyde incelemiştik Giriş kapasitesinin seçim kriteri Xcin - 0.1Rin dir. 2 kHzlik giriç sinyali için gerektt tapasite, Cm değerini hesaplayınız. Circuit parameters / Devre Parametreleri R1 = 53 k2, R, = 17 k2 R1 RD Cout Vout D VDD M2 Cin G Vin R2 RS cs O a. 74.19 nF O b. 86.55 nF O c. 49.46 nF O d. 61.82 nF O e. 43.28 nF
Q2. For the circuit shown below, sketch i, & Vo 60 a. Find the conduction angle of the thyristor. b. Find the average output voltage V. R-6.50 f- Go Hz = 27AL = 120x17X10 = 6.4092 075 LO = RrjX= Vo L-17mH 6.5+j6.469=9.128 (44595 075 75V( Es 24 Vm A e
2) With reference to the waveform illustrated as below, design and develop a circuit which can obtain the output waveform as given below.After developing the appropriate circuit formulate the equation for average value and rms value of output voltage and output current m wt -V, m m wt
2. A 12 phase balanced midpoint rectifier provides 200A at 200V to the load resistance. The load and filter are shown below (R in parallel with C, which is in series with the filtering inductor). Each source operates at 60Hz and has peak voltage of 340V=Vo, for example vi(t) 340cos(2p60t), and the other 11 sources out of phase (balanced) but with the same amplitude. (m=12) = a) What inductance value L that is needed to keep the peak-to-peak current ripple below ±15%? b) What is the capacitance value C that is needed to keep the peak-to-peak ripple below ±5% for this inductance value in part a)? #1 C V₁ = Vocos(wint) #2 * V2₂= Vocos(wint - #3 0000 *° * V3 = V₁ cos(wint - : Vm= V₁ cos(wint-(m-1)) #m + va(t) R