You obtained the following raw data when setting up a Biuret standard curve: Absorbancy 540nm BSA (mg/ml) 0.158 0.210 0.260 0.305 4 0.360 5 0.410 0.455 0.510 8 0.530 9 0.550 10 0.554 After blanking against a biuret-dH20 sample, the protein concentration of an unknown sample was determined using the same method and an absorbancy of 0.279 was obtained. Set up a standard curve, excluding outliers (experimental and statistical) and determine the protein concentration in the unknown sample in mg / ml (up to 3 significant fiqures). O12N3 67

You obtained the following raw data when setting up a Biuret standard curve: Absorbancy 540nm BSA (mg/ml) 0.158 0.210 0.260 0.305 4 0.360 5 0.410 0.455 0.510 8 0.530 9 0.550 10 0.554 After blanking against a biuret-dH20 sample, the protein concentration of an unknown sample was determined using the same method and an absorbancy of 0.279 was obtained. Set up a standard curve, excluding outliers (experimental and statistical) and determine the protein concentration in the unknown sample in mg / ml (up to 3 significant fiqures). O12N3 67

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter1: Introduction

Section: Chapter Questions

Problem 1.9QAP

See similar textbooks

Similar questions

10 Wavelength, 1. (nm) E (Red, µ.Mcm- ɛ(Yellow, µMr'cm¬1) Absorbance 500 0.0369 0.000549 0.405 430 0.00506 0.0167 0.474 An orange colored solution is prepared by mixing a red dye solution with a yellow dye solution and the absorbance was measured at the analytical wavelengths of 430 nm and 500 nm. The table provides the molar absorptivity for the red and yellow dye at each analytical wavelength. Calculate the concentration (in u.M) of the red and yellow dye in the mixture. [red] = [yellow] =
You obtained the following raw data when setting up a Bradford standard curve: BSA (mg/ml) Absorbancy 595nm 0 0.225 1 0.310 2 0.420 3 0.510 4 0.610 5 0.720 6 0.810 7 0.915 8 0.950 9 0.980 10 0.990 After blanking against a bradford-dH2O sample, the protein concentration of an unknown sample was determined using the same method and an absorbancy of 0.523 was obtained. Set up a standard curve, excluding outliers (experimental and statistical) and determine the protein concentration in the unknown sample in mg / ml (up to 3 significant figures).
In a Bradford assay, 11 µl of a protein isolate sample was diluted by adding 21 µl of water prior to the addition 2.0 mL Bradford reagent. Calculate the protein concentration (in mg/mL) of the original protein isolate sample whose absorbance reading at 595 nm is 0.304 after dilution. The protein standard solutions used for the calibration curve of the Bradford assay was constructed using bovine serum albumin (BSA) stock solution whose concentration is 200 µg/mL. The concentration and the corresponding absorbance reading at 595 nm of the protein standard solutions are summarized in the table below: Standard soln # 1 2 13 4 6 conc of BSA 12.00 24.00 36.00 48.00 60.00 (pg/mL) Absorbance at 595 nm 0.000 0.156 0.249 0.328 0.411 0.528 zNote: Final answer format must be x.xxx (three decimal places). Round off only in the final answer. Do not round off in the middle of the calculation.
The absorbance values at 250nm of 5 standard solutions, and sample solution of a drug are given below: Conc. (ug/ml) A 250 nm10 0.16820. 0.32930 0.50840. 0.66050 0.846Sample. 0.661Calculate the concentration of the sample
The absorbance of an unknown dye solution is measured to be 1.06 by a spectrometer. The calibration plot of the spectrometer is provided below. What is the molar concentration of the unknown sample (in mole L)? Absorbance vs. Molarity 18 y3 67024x-0.0343 16 14 12 1 0.8 0.6 0.4 0.2 01 0.2 0.000005 00001 0000015 Concentration of solutions, mol/L 0.00002 0.000025 000003 0 163e-5 O 2.35e-6 0 163 0 235 Absorbance
In a Bradford assay, 17 pl of a protein isolate sample was diluted by adding 24 pl of water prior to the addition 2.0 mL Bradford reagent, Calculate the protein concentration (in mg/ml) of the original protein isolate sample whose absorbance reading at 595 nm is 0,384 after dilution The protein standard solutions used for the calibration curve of the Bradford assay was constructed using bovine serum albumin (BSA) stock solution whose concentration is 200 ug/mL The concentration and the corresponding absorbance reading at 595 nm of the protein standard solutions are summarized in the table below: Standard soln # 3 6 conc of BSA Kug/mL) 12.00 24.00 36.00 48.00 60.00 Absorbance lat 595 nm 0.000 0.156 0.249 0.328 0.411 0.528 zNote: Final answer format must be x.xox (three decimal places) Round off only in the final answer. Do not round off in the middle of the calculation
A direct ELISA experiment was done to determine the amount of protein present in a sample. A standard curve was prepared by plotting log Absorbance versus log concentration of protein in (ng/mL). The equation of the line is Y= 0.895 X -1.25. If an unknown protein shows an absorbance of 1.23. Calculate the concentration of this protein in the sample in (ng/mL).
6. Blue Blue dye stock solution 0.293 M Absorbance at 630 nm 0.00265 Calibration curve y = 0.0833x A solution is prepared by diluting 2.79 mL of the blue dye stock solution to 25.00 mL. The measured absorbance for the prepared solution is listed in the data table. (a) What is the theoretical molar concentration? [Blue]theoretical x 10 |M (b) What is the experimental molar concentration? [Blue]experimental x 10 M (c) What is the percent error? Percent error (blue) = %
1. a 50.00-mL sample containging an analyte gives a signal of 11.5(arbitrary units). A second 50-mL aliquot of teh sample, which is spiked with 1.00-mL of a 10.0-ppm standard solution of the analyte, gives a signal or 23.1. what is the concentration of analyte in the original sample?
"[FeSCN2+]eq is calculated using the formula: [FeSCN2+]eq = Aeq/Astd x [FeSCN2+]std where Aeq and Astd are the absorbance values for the equilibrium and standard sample respectively." I am confused about what Aeq and Astd mean. We did an experiment where we measured the absorption of this chemical formation and I got around 0.18. Is that one of the values?
The concentration and absorbance data below were collected for compound X. A sample of compound X of unknown concentration has a corrected average absorbance of 0.5621 (3 replicate measurements). Calculate the y-intercept. CONCENTRATION (mg/mL) ABSORBANCE 5 0.422 10 0.510 15 0.621 a. 0.299 b. 0.222 c. 0.319 d. 0.553
This graph shows an absorbance vs concentration curve for Co2*(aq) solution. Sample Standard Curve 1.20 1.00 800 .600 a 400 e 200 20 02 0 080 100 Co2. conc. (M) .020 040 OGO 120 140 160 • Slope - 6.414 Intercept -7.799991E 03 Con. Coef - 9791 Assuming that Beer's Law holds, A = Elc, and the cuvette was a standard 1-cm optical path, what is the molar absorptivity coefficient for the Co2* solution? a. 3.58 x 103 cm" o b.3.58 x 103 cm M-1 OC 7.80 x 103 cm1M-1 O d. 6,414 cm1M1