Which topology requires a central controller? a) Mesh 1. b) Star c)Bus d )Ring ii. Which of the following codes can't be a valid MAC48 address? a) a0-46-b6-55-34-d2 d)45-4d-b4-44-40-76 b) d8:3f:7c:00:67:88 c) 76:23:d7:86:57:g4 iii. Mail services are available to network user through the c) Transport --layer d) Application a) Data link b) Physical

Which topology requires a central controller? a) Mesh 1. b) Star c)Bus d )Ring ii. Which of the following codes can't be a valid MAC48 address? a) a0-46-b6-55-34-d2 d)45-4d-b4-44-40-76 b) d8:3f:7c:00:67:88 c) 76:23:d7:86:57:g4 iii. Mail services are available to network user through the c) Transport --layer d) Application a) Data link b) Physical

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

con con of son The first 2 pins of the analog pins in Arduino are used to transmit and receive data (TX and RX) O a. False O b. True Which of the following parameters is not a required part in the ARDUINO sketch "for" loop? O a. Initialize O b. Increment OC. Serialprint O d. Condition When an overflow occurred, the C bit in the STATUS register is O a. None of these O b. 0 Oc. Not affected Od 1
3-bit "gray" code numbers forward (up). counting / repeating synchronous counter circuit using JKFF design. a)with truth table b)Karnaugh maps simplification c)circuit drawing
Question 1 Perform the following numbering conversion and arithmetic. Show all the steps clearly. а) i) 12BF.FC916 to Decimal number ii) Add these two Octal numbers 4568 and 3578. Convert the answer into Binary number. iii) Add these two Decimal numbers of 243 and 87 in Binary Coded Decimal (BCD). Give the answer in 16-bit BCD form. b) Determine the -91 10 dan -11710 as an 8-bit number in the sign magnitude, l's complement and 2's complement forms. Table 1 shows THREE (3) set of Gray Code's number. Convert the Gray code into Binary numbers and their corresponding ASCII Codes. c) Table 1 Set A 00110111 Set B 00100011 Set C 01100000
A parity bit is "1" on a system which uses odd parity. The data is "C8". The data is: A. Good B. Corrupted C. Artificial D. Real
A multiplexer is a device that selects one among N analog or digital inputs and forwards the selected input to a single output line. Answer the following questions. (Note: You should show all the steps) a) If the mux has 4 inputs, how many control inputs are needed? b) Draw the truth table of 4-to-1 multiplexer.
Solve the problem and simplify the output function using Quine–Mc Cluskey Methods. The following requirements must be met in solving the problem. Requirement:a. Truth Tableb. Timing Diagramc. Quine – Mc Cluskey Method d. Logic Diagram A private company wants to decide on a certain issue. Each of the four officials has an equal share of voting right. At least two of them must approve the solution in order to implement it. Each of them has a switch which closes to vote YES and open to vote NO.
Answer the following questions: 1. Design a 8 bit "shift left-shift right" register. 2. Design a 8 bit up counter. 3. Difference between sequential circuit vs combinational circuit. 4. Design a 8:1 multiplexer using 4:1 multiplexer and 2:1 multiplexer. 5. When designing register file, we used multiplexer to read from a specific register of that register file. However, to write in the register file, we didn't use demultiplexer. Why ? 6. In our designed register file, we can write one data at a time. But if we want to write two data at a time,what should we do ? 7.Logisim simulation: A. Design a 8 bit register file with 10 registers. B. Design an ALU with AND, OR, XOR, NOT, ADD and SUBTRUCT operations that can use the above register file. C. Create a single cycle data-path between register file and ALU. Save 1 digit of your NSU ID in each register of your register file before running instructions given below.E.g. for id: 1831565042, save 1 in first register, 8 in second, 3 in third and…
5. The following diagram represents a four-bit ring counter. Assuming a starting state of Q3 = 1 and Q₂ = Q₁ = Qo= 0, complete the timing diagram. Explain how this counter works. CLK 23 2₂ 2₁ 20 D CLK Q3 D 22 >CLK D 2₁ >CLK D CLK Lot
RESEARCH Draw at least 4 typrs of IC. Discuss the different IC packages. How to identify the pin numbering of IC? Proper handling of IC. What is seven-segment display? How to produce the required decimal digit from 0 through 9 using seven-segment display? Uses of seven-segment display.
We want to design a digital circuit that converts Gray code (ABC) to Binary code (xyz). Set up a 8-to- 1 line multiplexer so that the output gives y as a function of ABC. "A" is given to the most significant bit of the control inputs of the multiplexer. "C" is given to the least significant bit of the control inputs of the multiplexer.
Question 1 [Svalan i (a) Determine the largest number for Octal number that can be expressed with 4-bit. Convert the number to a Binary number and Gray code. Table 1 shows five (5) set of numbers that represented in BCD number. Convert the numbers into Decimal number and by using Appendix 1, decode the numbers into ASCII coded message. (b) Table 1 Set A 10011000 Set B 01010001 Set C 00110110 Set D 10000100 Set E 00100111 Determine the simplified Sum-of-Product (SOP) expression for the given expression by using Karnaugh map. (c) Р(4, В,С, D) - яМ(3,7,12,13,14,15) D(5,6,11)
a) 16 pieces of 32Kx8 SRAM are connected to 8088 to address the 00000H-7FFFFH memory region. This circuit uses 3 separate decoders to select the appropriate memory regions. Draw this circuit showing the address, data and control connections. (Do not buffering.) b) 8 pieces of 32Kx8 SRAM will be connected to the circuit in a way to form the address space C0000H-FFFFFH. Accordingly, draw the new circuit to be added to the above circuit. (You can use additional decoder or gate circuit.)