Two tanks are connected in the following unusual manner. F₂ Notes: F₂ x+ h₂ F₂ a. What are the algebraic equations & ODEs that can be used to find h₁, h₂, F₂, & F3 as functions of time for any given variations in inputs. b. Identify all input & output variables. The density of the incoming liquid, p, is constant. The cross-sectional areas of the two tanks are Ą and Ą₂. F₂ is positive for flow from Tank 1 to Tank 2. h₂ The two valves are linear with valve coefficients C₂ and C². Both tanks are open to the atmosphere.

Two tanks are connected in the following unusual manner. F₂ Notes: F₂ x+ h₂ F₂ a. What are the algebraic equations & ODEs that can be used to find h₁, h₂, F₂, & F3 as functions of time for any given variations in inputs. b. Identify all input & output variables. The density of the incoming liquid, p, is constant. The cross-sectional areas of the two tanks are Ą and Ą₂. F₂ is positive for flow from Tank 1 to Tank 2. h₂ The two valves are linear with valve coefficients C₂ and C². Both tanks are open to the atmosphere.

Name: Two tanks are connected in the following unusual manner.F₁Notes:h₂F₂J
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Two tanks are connected in the following unusual manner.F₁Notes:h₂F₂Jh₂What are the algebraic equations & ODEs that can be used to find h₁, h₂, F₂, & F3 asfunctions of time for any given variations in inputs.b. Identify all input & output variables.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

b) A pitot tube flow sensor is used to measure the flow rate in a pipe, as shown in Figure Q4. Impact Probe P1 Direction of Flow Static Probe P2 Differential pressure transducer Figure Q4 A manometer is used to measure the differential pressure, showing a difference in fluid level of 150 mm between the two probes. Calculate the differential pressure if the liquid has a density of 900 kg / m3, expressing your answer in pascals and also bar. (Gravitational acceleration, g may be taken as 9.81 m/s².) (Question 4 continues on the next page.) Page 5 of 14 (Question 4 continues below.) c) The velocity of the fluid is given by: 2(P1-P2) V = (m/s) where P1 - P2 is the differential pressure, measured in Pascals. Calculate the linear flow rate in m/s. d) If the diameter of the pipe is 200 mm, calculate the i) volumetric flow rate in m3/s ii) mass flow rate in kg/s
sn3 Read and analyze the following questions and answer themvery carefully. Show your complete (show unit cancellation)and step-by-step solution and box your final answer. Use threedecimal places.
1. For the following concentration expressions, indicate whether they are uniform or nonuniform and in how many dimensions (OD, 1D, 2D, or 3D), and steady or unsteady. Then for the following control volume and origin, and table of constants, use Excel or Matlab to graph profiles that show how concentration changes within the control volume and over time to a limit of 20 for the following: C(x,0,0,0), C(0,y,0,0), C(0,0,z,0) and C(0,0,0,t). On each graph, show which parameters are held constant, the CV boundaries, and the point where all four plots overlap. 20 C(x=0) 10 a 0.0001 b 0.001 | 20 0.01 k 0.1 100 All of the following functions are C(space, time) and so not necessarily just x as suggested. a. C,(x)= C,(x = 0)x exp{- ax}
Q: for the following equation, what are the units of x., u, and a if X, is the distance in m. t, is the time in second? [X. x3 = + u?t +
. I am planning to perform some volume-flow rate measurements in the Fluid Mechanics Laboratory. For this, I need a volumetric measuring tank (graduated cylinder) and a stopwatch. I considered the volume of the measured tank as 15 gallons and a stopwatch with reaction time as 1/10th of a second (though resolution of 1/1000th of a second). What is the volume flow rate if it takes 5 minutes to fill a 15-gallon of tank? Determine the smallest division to be on the tank in order to estimate the volume flow rate within an accuracy of ± 0.05 gpm.
For the Following question Graph all 4 : [I just need all 4 graphs and please explain and make clean solution] Position vs time Velocity vs time Acceleration vs time Force vs time [For your convenience, I have solved the numerical solutions for the problem] (Please Look at the picture since it is much cleaner) Question : A 550 kilogram mass initially at rest acted upon by a force of F(t) = 50et Newtons. What are the acceleration, speed, and displacement of the mass at t = 4 second ? a =(50 e^t)/(550 ) [N/kg] v = ∫_0^t▒(50 e^t )dt/(550 )= v_0 +(50 e^t-50)/550=((e^t- 1))/11 x = ∫_0^t▒(e^t- 1)dt/(11 )= x_0 +(e^t- t - 1)/(11 ) a(4s)=(50*54.6)/550= 4.96[m/s^2 ] v(4s)=((e^4-1))/11= 4.87[m/s] x(4s)=((e^4- 4 - 1))/11= 4.51 [m]
Q1. The image below shows an example of "absolute dependent motion analysis", where the motions of two objects depend on each other, and the goal is to find the relations in their motions (i.e., in their positions, velocities, and accelerations). Please put the suggested steps of analysis in the correct order. VA A B VB Differentiate the entire equation with respect to time, and extract the relation in velocities. Repeat for acceleration if needed. Set up a coordinate (s) along the direction of motion from a fixed point (O) or a fixed datum line. Represent the positions of the objects respectively. In some cases intermediate objects need to be considered too and their positions need to be represented as well. Recognize the constant length(s) and find the depending geometric relations between the position variables.
The amount of time it takes for a pendulum to swing “to-and-fro” through one complete cycle is called the “period” and is calculated using the following equation: where T = period in seconds, I = mass moment of inertia, m = mass of pendulum in kilograms g = gravitational acceleration, 9.8 m/s2, h = effective length of pendulum in meters What is the appropriate unit for I if the preceding equation is to be homogeneous in units? Please show all of your work.
Q1/A/ The heat capacity, Cp, depends on temperature and can be expressed as a function of temperature: Cp = A + BT + CT² + DT-² R The enthalpy change, AH which is equal to heat is given by: -T2 AH = Q = n CpdT T1 Write a script file to calculate the heat required if we need to increase the temperature of 15 kgmole/hr of methane from 298.13 to 373.13 K. Where A=1.702, B-9.081*10-³, C=-2.164*10-6, D=0, and R-8.314. B/ State whether the following are true (✓) or false (x) and correct the false statements 1- We can use the built-in functions in naming variables when they are in uppercase. 2- In the symbolic math toolbox, symbolic objects can also be numbers. The numbers must be typed as strings. 3- Two vectors can be multiplied only if they have the same number of elements. 4- All variables in MATLAB are arrays. 5- The only difference between plot and line commands is the latter does not have the line specifier. 6- In the disp command which is used to display output (like with the fprintf…
Problem 5.1 When a liquid flows over a surface, the velocity may vary with position. The equation or graph that describes this variation is known as the velocity profile. A thin layer of liquid, draining from an inclined plane as shown in the figure, will have an analytic velocity profile described by the following equation. u Uo = U. [2) -²] where U is the surface velocity, i.e., velocity of the water at the surface of the layer, u is the velocity of the water at any y-position in the layer, and h is the thickness of the layer. A graph of this velocity profile is shown in the figure. h u(y) Direction of gravity a) If the plane has constant width b into the paper, develop an expression for the volumetric flow rate in the film in terms of h, Uo, and b. [Hint: Use a differential area element dA = b dy and integrate from y = 0 to y = h.] b) Calculate the mass flow rate of liquid down the inclined plane, in kg/s, if the liquid has a specific gravity of 0.87 and b = 0.3 m, h = 5 mm, and U₁…
A chamber of unknown volume is filled with an unknown amount of ideal gas. A cylinder with an open bottom and calibrated volume is connected to the chamber and is closed with a movable piston. A gas pressure sensor is also mounted on the chamber as shown in the figure. The whole experimental setup is kept at a constant temperature of 300 K. Doris moves the piston from mark 0 to mark 200 mL in steps of 50 mL and records the corresponding pressure in the chamber (see the table below). She moves the piston very slowly and waits several minutes before recording the pressure values. VCyl(mL) P(105N/m2)) 0 4.35 50 3.85 100 3.50 150 3.15 200 2.90 Determine the volume of the chamber using Doris's data in the table. (Note: This is a problem that requires linearization of data.) Determine the number of moles of gas. (Note: This is a problem that requires linearization of data.)
From the image below, and using the given datum, match the variable expressions to their position coordinates, SA, SB and SC, where s A is for block A, $3 is for pulley B, and so is for pulley C. If an expression does not match any position coordinate, then match it to the "None" option. 1.k-q 2.0 3.p 4. k SA Datum bc SC k ✓ None SB ФВ A Р ⒸOF