The two lever assembly shown below is subject to a static load F = 8250 lb.%3D(a)identical links BD can be made from based on the stress in the middle of each link.Specify the lowest-strength alloy steel from Appendix A-10 that the two(b)is the minimum recommended diameter that the pins can be machined to?The pins at B and D are made from SAE 4140 OQT 900 alloy steel. WhatWhat is the bearing stress on the pins at B and D based on the pin(c)diameter you calculated in part (b) above?9 in8 inCBTop ViewAВCB0.75 in --0.31 inF 0.31 inSide ViewFront View

Answered: The two lever assembly shown below is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook. Condition #2: The same structural support of the basic size determined in Condition 1 is subjected to a tensile load of 15 kN that is repeated several thousand times over the life of the machine. This load is not an addition to the 20 kN. Specify a suitable steel that is suitable to this application based on the basic size determined in Condition #1. Loading of Condition #1 does not apply here. Condition #3: The same structural support from Condition 2 is heated from room temperature of 25°C. The support is placed inside a frame on both ends. There is a total clearance of 0.2 mm between the support and its frame. Initial length of the rod is 200 mm. Specify the…
L21. Figure P4-21 shows an anvil for an impact hammer held in a fixture by a circular pin. If the force is to be 500 lb, specify a suitable diameter for the steel pin if it is to be made from SAE 1040 WQT 900. 4-21
A structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook.
Condition #1: Å structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook.
The butt connection shows 8- 22 mm diameter bolts(bolt hole dimension of 26 mm) spaced as shown below. Steel strengths are Fy 248 MPa and F, = 400 MPa. Use NSCP 2010/2015 Code Provisions %3D Calculate the design tensile strength based on the following: Based on the gross area of the plate Based on the net area of the plate. Based on block shear strength. CS Scanned with CamScanner
M P 1: Y A :s.google.com Q1 * Find the number of bolts M8 1 which made from SAE Grade 4 steel that should be used to provide a clamping force of 60 KN between two components of a machine. Also, specify the required tightening torque. (Hint: assume that cach bolt is limited to be stressed to 65% of its proof strength). 1 Add file Q2 * A flat plate with a central hole is subjected to an axial tensile force F of 9.8 KN, as shown in the figure below. Calculate the minimum thickness t of the plate. Given that the material of the plate can support maximum tensile stress of 75 N.mm, w = 10 cm and d = 3 cm. Thickness =t F 1 Add file Submit Clear form II
Select a standard threaded round rod to support a factored tensile load of 35 kips (service tensile load = 25 kips) using A36 steel. (answer 1 1/4-in rod LRFD and ASD)
4) An electric motor purchased by your employer surprisingly arrived without a keyway in the shaft. The motor has power rating of 7.5kW & 1,800rpm & has a shaft of 17mm. It will be used to drive a centrifugal pump using cast iron sheave. Design the square key to be used in the assembly based on maximum bearing & shearing stresses of 580MPa & 370MPa, respectively, and factor of safety of 5.
For a bolted assembly with 8 bolts, the stiffness of each bolt is k_b = 1.1 N/mm and the stiffness of the members is k_m = 2.8 N/mm at each bolt location. The joint is subject to occasional disassembly for maintenance and should be preloaded accordingly (to 75% of the proof stress). Assume the external load is equally distributed to all the bolts. It has been determined to use M6 × 1 class 5.8 bolts with rolled threads. Determine the maximum safe working load that both limits the stress in the bolts to be below the proof stress and ensures that the members do not come out of compression. Express your answer in units of kilonewtons.
A bolted joint is to have a grip consisting of two 14-mm steel plates and one 14R metric plain washer to fit under the head of the M14 x 2 hex-head bolt, 50 mm long. (Hint: Look up table A-31 and A-33 in the textbook of Shigley's Mechanical Engineering Design, 8th Edition) (a) What is the length of the thread LT for this diameter metric coarse-pitch series bolt? (b) What is the length of the grip l? (c) What is the height H of the nut? (d) Is the bolt long enough? If not, round to the next larger preferred length. (e) What is the length of the shank and the threaded portions of the bolt within the grip?
An aluminum rod, made from alloy 6061-T6, is made in the form of a hollow square tube, 2.25 in outside with a wall thickness of 0.125 in. Its length is 16.0 in. It carries an axial compressive force of 12 600 lb. Compute the resulting design factor. Assume that the tube does not buckle. Mott, Robert L.; Vavrek, Edward M; Wang, Jyhwen. Machine Elements in Mechanical Design (2-downloads) (What's New in Trades & Technology) (p. 211). Pearson Education. Kindle Edition.
Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. For condition 1: It was given to you to use SAE1040 hot rolled steel. In the high-stakes project, you select a different steel for the analysis for condition 1 and determine the basic size A-10 Typical properties of carbon and alloy steels. Ultimate strength,s, Yield strength, s Percent elongation Material SAE no. Condition ksi MPa MPa Annealed Hot rolled Cold drawn 1020 57 65 75 393 448 517 43 48 296 331 441 36 36 20 1020 1020 64 Annealed Hot rolled Cold drawn WQT 700 WQT 900 WOT 1100 WQT 1300 1040 75 90 517 51 30 25 1040 621 669 876 814 738 414 565 641 621 552 60 1040 97 16 19 22 24 1040 1040 1040 127 118 107 93 90 80 1040 87 600 63 434 32 1080 Annealed OQT 700 OQT 900 OQT I100 OQT 1300 614 1303 1234 1000 89 54 372…

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS