The rigid bar ABC shown in Fig. is hinged at A and supported by a steel rod at B. Determine the largest load P that can be applied at C, if the stress rod is limited to 207MPa and the vertical movement of end C must not exceed 0.25mm. Ans: P= 2.111KN 0.6m B Steel L= 1.22 m A= 322 x 106 m² E= 200 GPa 0.9m P

The rigid bar ABC shown in Fig. is hinged at A and supported by a steel rod at B. Determine the largest load P that can be applied at C, if the stress rod is limited to 207MPa and the vertical movement of end C must not exceed 0.25mm. Ans: P= 2.111KN 0.6m B Steel L= 1.22 m A= 322 x 106 m² E= 200 GPa 0.9m P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 3 of 12 View Policies Current Attempt in Progress Answer: Pmax= eTextbook and Media A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 3.5 in.². Assume a = 4.00 ft and b = 4.80 ft. If the normal stress in each member must not exceed 60 ksi, determine the maximum load Pmax that may be supported by the structure. Save for Later b -/15 kips ||| Attempts: 0 of 3 used *** Submit Answer
1. Calculate the change in length of the bar. 2. Determine the stress of member BC. A steel bar AD has a cross sectional area of 250 mm? and is loaded by a force P:=12kN, P2=8kN, and Ps=6kN. The length of the segments are a=1.5m., b=0.60m. 3. By what amount should the load P3 be increased so that the bar does not change in and c=0.90m. E=200 000 Mpa. length when the three loads are applied? P1 P2 P3 B C a=1.5 b=0.6 b=0.9
Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of the link and its length are given in the table below for cach student. The alloawble stress of link BD is 200 MPa. a) Determine the maximum possible value of the load P b) If P-90 kN, determine the change in temperature needed for link BD to have no change in length. Given Me=12*10/"C, E,200 GPa B A 0.4m 0.2m
20 KN . 38 mm Ø 1.0 m 40 KN 40 KN B 64 mm Ø1 1.5 m C Fig.pl-01 P2. Solve Problem P1-01 if rod BC is a hollow rod whose inner diameter is 38 mm. All' other data remain the same. 4 m
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.
The rigid bars shown are separated by a roller at Cand pinned at A and D. A steel rod at B helps support the load of P 55 kN. Compute the vertical displacement of the roller at C. Given: a - 2 m, b 3 m, C= 3 m, d 1.9 m. E - 203 GPa, A 337 mm and L-2 m. Answer must be in mm.
2. A horizontal bar of negligible mass, hanged by hinge at point (A) as shown. The bar is assumed to be rigid and is supported by vertical bronze bar of (2m) length, a steel bar of (1m) length, using the data given below; determine the stress in each bar. Steel Bronze Area (mm) E (GPa) 600 300 200 83 2m Br 1m St A O 0.6m 1m 0.8m 50KN
A circular cross section cylinder containing oil, has an internal bore of 30cm diameter. The cylinder is 1cm thick If tensile stress in the cylinder must not exceed 75MPa, maximum load P which may be supported on piston sliding in the cylinder is
A bar, 12 mm in diameter is acted upon by an axial load of 20 kN. The change in diameter is measured as 0.03 mm. DeterminePoisson’s ratioYoung’s modulusBulk modulus Assume modulus of rigidity as 80 GPa
Q1) A (25mm) square cross-section bar of length (300mm) carries an axial compressive load of (50KN). determine the stress set up in the bar and its change of length when the load is applied - for the bar material. Ans. (E = 200GN/m). (ans. 80 * 106 , 0.12mm) %3D A Q2) A steel tube, (25mm) outside diameter and (12mm) inside diameter, carries an axial tensile load of(40KN). What will be the stress in the bar? What further increase in load is possible if the stress in bar is limited to 225MN/m?
Q1) A (25mm) square cross- section bar of length (300mm) carries an axial compressive load of (50KN). determine the stress set up in the bar and its change of length when the load is applied -for the bar material. Ans. (E = 200GN/m). (ans. 80 * 106 , 0.12mm) %3D A Q2) A steel tube, (25mm) outside diameter and (12mm) inside diameter, carries an axial tensile load of (40KN). What will be the stress in the bar? What further increase in load is possible if the stress in bar is limited to 225MN/m? Q3 A (25mm) diameter bar is subjected to an axial load of (100KN). under the action of tis load a(200mm) gage length is found to extend (0.19*10 mm). determine the modulus of elasticity for the bar material. Ans.(E = 210GN/m) %3D
The assembly shown consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 7 mm, between the lower end of the steel rod and its pin support at C. The stress in the aluminum rod (in MPa) when the lower end of the steel rod is attached to its support is: Eal= 70 GPa, Est 200 GPa. Aa 240 mm2, A= 170 mm?. 0.75 m 1.5 m Aluminum L= 2 m Steel