Task 3. Using the diagram below, compute the power supplied to the electric heater using electrical power formulas. Рассчитайте мощность, подводимую к электронагревателю, используя Формулы электрической мощности. I V = 120 v Heater R = 12 1

Task 3. Using the diagram below, compute the power supplied to the electric heater using electrical power formulas. Рассчитайте мощность, подводимую к электронагревателю, используя Формулы электрической мощности. I V = 120 v Heater R = 12 1

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 6RQ

See similar textbooks

Similar questions

A) An equalizer is a jumper used to parallel the series field of two compound DC generators when the two generators are being run in parallel to share an electrical load. a) true b) false B) The ohmic value of an equalizer is not important as long as it is made out of copper. a) true b) false C) How is the efficiency usually expressed?a) in watts b) in kilowatt-hours c) in percentage d) none of the above
1- The below given nameplate a) How can it be run in a network of 50 Hz? b) Will there be any changes in the number of revolutions? Explain in detail? CHICAGO Electric Power Tools INDUSTRIAL МОTOR - 1 НР MODEL: 92105 VOLT: 120 AMPS: 5.5 POLES: 4 HP: 1/2 HZ: 60 RPM: 1725 PHASE: DATE: Oct 18,07 SERIAL#: 070043 MADE IN THAILAND
circuit breakers. A bimetallic strip is MOST associated with a. magnetic b. thermal С. oil d. instantaneous
Set the supply voltage values equal to standard single-phase socket used in Finland. The load is an electric heater with a nominal value of 500 Watts, which can be assumed completely resistive in this task. Return a) Wiring diagram b) the input and output voltage waveforms (as a function of time) c) the input and output current waveforms (as a function of time) d) Average and peak power transferred to the radiator based on simulation (resistor) Figure 1. The load of the simulation task is an electric heater with nominal power of 500 W, and it could look like this. The heater is connected to a typical single-phase socket.
In a wattmeter, for producing the deflection torque a. Only Voltage coil is energized O b. Both voltage coil and current coil will be energized O c. Only Current coil is energized O d. Either voltage coil or current coil will be energized
False statement of Generators А. Consists of two rotating part of stator and rotor В. Convert mechanical energy to electrical energy C. Can be single phase or three phase generators D. Electricity generated based on Faradays Law
Main goal of using feed water heaters is to minimize the amount of heat addition in steam generator. Select one: with explanation True False
1.3 A 240 volts 50 Hz single phase ac source supplies a series load consisting of a resistor (40 ohms), a reactor (127.324 mH) and a capacitor (318.3 µF). Suppose that the frequency of the source can be varied at will. 1.3.1 Determine the maximum load current. 1.3.2 Determine the source frequency for maximum load current. 1.3.3 What is the name of this frequency? 1.3.4 Determine the load power factor. 1.3.5 What is the name of the source
In a 500/250 volt 3-wire d.c. system, there is an out of balance load of 200 kW on the positive side. The loss in each balancer set is 10 kW and the current in the negative main is 2800A. Calculate the current in each armature of the balancer set and the total load on the generator.
The following fuel pump is being controlled by a computer using the PWM technique applied to the low side driver. FUEL PUMP RELAY PCM FUEL PUMP CONTROL rUL PUMP MOTOR RUN SICNAL A) Fill the following table regarding the operation of the pump motor Duty cycleMotor Voltage Motor speed 10% 20% 30% 40% 50% 1500 RPM СОРHONE B) Plot the driving PWM signal which has a duty cycle of 40% ON POCOPHONE F1
On an induction type energy meter, is written "1200 rev/kWh". If it is to be used as an approximate wattmeter that is read off in rpm, a 400-watt load would read as (а) 10 грт (c) 8 rpm (b) 6 гpm (d) 24 грm rpm
A 200V long-shunt generator delivers 100A, has an armature resistance of 0.05Ω, a series field resistance of 0.25Ω and a shunt field resistance of 200Ω. If a feeder resistance of 0.05Ω and a brush contact drop of 2.5V are considered, what will be the generated voltage (in Volts) of the machine? use two decimal places if the answer is not exact and do not include the unit anymore.