Superheated steam at 18 MPa, 560 °C enters the steam turbine. The pressure at the exit of the turbine is 0.06 MPa and saturated liquid water leaves the condenser at 0.06 MPa. Pressure is increased to 18 MPa again after the pump. Find: (a) Sketch the process on a T-s diagram. (b) The net work per unit of steam flow in kJ/kg. (c) Heat transfer to steam passing through the boiler, in kJ/kg.

Superheated steam at 18 MPa, 560 °C enters the steam turbine. The pressure at the exit of the turbine is 0.06 MPa and saturated liquid water leaves the condenser at 0.06 MPa. Pressure is increased to 18 MPa again after the pump. Find: (a) Sketch the process on a T-s diagram. (b) The net work per unit of steam flow in kJ/kg. (c) Heat transfer to steam passing through the boiler, in kJ/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes saturated. It is withdrawn and reheated to 340°C. After further expansion in the turbine to 160 , part of the steam is extracted for feedwater heating. The remaining steam expands to the condenser pressure of 0.018 MPa. For 1kg of steam, find Wnet, Ec, Ee and the ideal steam rate. Remember:1. For values taken from the steam tables: Use them as is, do not round off.2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places.PLEASE USE THE STEAM TABLE PROVIDED: https://docs.google.com/document/d/1crebk95lXFEAR5d6Y6LymXJNraO9WLgtNjquSlVOvVs/edit
TH 3 kg of air as an ideal gas undergoes a Carnot refrigeration cycle as shown The isothermal expansion occurs at 300K and isothermal compression occurs at 600K. The heat transfer to air during isothermal expansion is 125 kJ. Pressure at the end of figure. isothermal expansion is 75 kPa. a. Find pressure at the beginning of the isothermal expansion. Show all work and explain your numbers. b. Sketch this cycle on the T-s diagram. Show on the diagram the system states (1,2,3, and 4), the cycle direction, and the cycle work (not its amount)
Steam at 5.1 MPa and 370°C enters a turbine and expands until it becomes saturated. The steam is withdrawn and reheated to 340°C. After expansion in the turbine to 160 ℃, m1 kg is extracted for feedwater heating. The remaining steam expands to the condenser pressure of 0.018 MPa For 1 kg of steam, find W_net , e_c , e_e and the ideal steam rate.
Problem (8.2) A steam turbine develops 3000kW when the steam is supplied at 10 bar and 250°C. The vacuum in the condenser is maintained at 65 cm of Hg. The barometric reads 75.2 cm of Hg. The rise in temperature of cooling water is limited to 15°C. The temperature of the condensate coming out of condenser is 35°C. Find, (a) specific steam consumption of the plant, and (b) quantity of cooling water circulated through the condenser per hour. Assume there is no leakage in the condenser. Ans.[(a) 4.8 kg/kW.h, (b) 447 tons/h]
1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes saturated. It is withdrawn and reheated to 340°C. After further expansion in the turbine to 160 , part of the steam is extracted for feedwater heating. The remaining steam expands to the condenser pressure of 0.018 MPa. find Wnet, Ec, Ee and the ideal steam rate. Remember, 1. For values taken from the steam tables: Use them as is, do not round off. 2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places. 3. PLEASE USE THE STEAM TABLE PROVIDED: https://drive.google.com/drive/folders/15t3WMv7xSTHmwXWXp0X2ZV6aYWhXuRCS?usp=sharing
An ammonia refrigeration compressor takes its suction from the evaporator, at a temperature of-200F and a quality of 95%. The compressor discharges at a pressure of 100 psi, liquid ammonia leaves the condenser at 500F.(a)Determine the heat absorbed by the evaporator in kJ/kg. (b)Determine the heat rejected to the condenser in kJ/kg. (c)Determine the COP. (d)Determine the horsepower per ton of refrigeration. (e)Determine the quality of refrigerant upon entering to the evaporator
Air goes through a Brayton cycle gas turbine, entering the compressor at 11 °C and 108 kPa. When it reaches the turbine inlet, the air is at 1,061 °C and 1.23 MPa. What is the net change in specific enthalpy of the working fluid after going through the compressor and heat addition processes? You may assume that the specific heat capacity c, is a constant 1.005 --1. kJ-kg 1.K1 throughout the whole cycle. Give your answer in kJ-kg1 to one decimal place.
Saturated steam at 40∘C is to be cooled to saturated liquid in a condenser. The mass flow rate of the steam is 17.3 kg/s . Assume no pressure loss. a)Determine the rate of heat transfer. Q = ? MW
Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the firstturbine until it is just dry saturated, then it is re-heated to 400 °C and expandedthroughthe second-stage turbine. The condenser pressure is 0.04 bar. Determine the specific work output of the system to 3 d.p? what is the specific entalphy in kJ/kg for state 2?
P3.4 The condensing and evaporating temperatures of a standard vapor compression cycle using R134a are 5°C and 35°C respectively. The heat absorption rate is 12 kW. Calculate (i) the refrigerant flow rate, (ii) the work input to the compressor, and (iii) the COP of the cycle. [Answers: (i) 0.07875 kgs¯¹, (ii) 1.52 kW, (iii) 7.89]
Provide the solution and diagram. A 120 tons refrigeration system with COP of 5 has a condenser which is to be cooled by means of a cooling tower. Air enters the tower at 25 oC db and 50% RH and leaves at 35 oC db and 80% RH. Find the volume of air needed m3/hr. At 25oC and 50% RH: h = 50 KJ/kg, v = 0.86 m3/kg At 350C db and 80% RH: h = 108 A. 7.51 m3/s B. 2.34 m3/s C. 4.98 m3/s D. 3.16 m3/s
3. A water-tube boiler having a heating surface of 325.23 m² evaporates 6349.21 kg of water in an hour from a feed temperature of 66 °C. Boiler pressure is at 1.04 MPaa and the steam quality at the boiler outlet is 99 %. What percent of its rated Bo. Hp was the boiler developing?