Situation 2: A square hollow steel strut of thickness 10 mm is pin connected to two connector plates of thickness, 12 mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to the concrete base by 4-16 mm diameter anchor bolts. The diameter of the pin is 16 mm. 48 kN 4. Which of the following most nearly gives the bearing stress between the strut and the pin? a. 150 MPa steel strut c. 120 MPa b. 140 МPа d. 125 MPa 30 5. Which of the following most nearly gives the shearing stress in the pin? c. 103.37 MPa d. 119.37 MPa a. 110.46 MPa ь. 126.39 МPа base 6. Which of the following most nearly gives the shearing stress in the anchor bolts? c. 51.69 MPa d. 47.16 MPa plate a. 55.04 MPa b. 59.68 MPa connector plate anchor bolt

Situation 2: A square hollow steel strut of thickness 10 mm is pin connected to two connector plates of thickness, 12 mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to the concrete base by 4-16 mm diameter anchor bolts. The diameter of the pin is 16 mm. 48 kN 4. Which of the following most nearly gives the bearing stress between the strut and the pin? a. 150 MPa steel strut c. 120 MPa b. 140 МPа d. 125 MPa 30 5. Which of the following most nearly gives the shearing stress in the pin? c. 103.37 MPa d. 119.37 MPa a. 110.46 MPa ь. 126.39 МPа base 6. Which of the following most nearly gives the shearing stress in the anchor bolts? c. 51.69 MPa d. 47.16 MPa plate a. 55.04 MPa b. 59.68 MPa connector plate anchor bolt

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.1P

See similar textbooks

Similar questions

Item 2 Figure 1 A D of 1 -0.5 m- 400 KN B -0.5 m C 0.4 m Part A The assembly consists of two posts AD and CF made of A-36 steel and having a cross-sectional area of 1100 mm², and a 2014-T6 aluminum post BE having a cross-sectional area of 1700 mm². If a central load of 400 kN is applied to the rigid cap, determine the normal stress in each post. There is a small gap of 0.12 mm between the post BE and the rigid member ABC. (Figure 1) Enter your answers, separated by commas. JAD, CF, OBE = Submit O Π| ΑΣΦ ↓↑ My Answers Give Up vec ? MPa Provide Feedback Continue
The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec =23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f'c = 25MPa 800 730 N12 ligs (fx.t-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Use the Transformed section approach considering the presence of steel. Calculate the concrete area and transformed steel area in both tension and compression shown in Figure 3. n=Es/Ec Ast=1232mm^2 Use n-1 for the transformed area to do the calculate. Unit: mm^2 with two decimal
Question 8 1 p The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec=23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f'c = 25MPa 800 TE 730 N12 ligs (fsv.t-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Calculate the concrete stresses in tension and compression of the reinforcement concrete beam shown in Figure 3. Compression concrete stress Choose ] Tension Concrete stress Choose]
A flexural member is fabricated from two flanges plates 1/2" x 18" and a web plate 5/16" x 20". The yield stress of the steel is 36 ksi. a. Compute the elastic modulus and the yield moment with respect to major principal axis. b. Compute the plastic modulus and the plastic moment with respect to major principal axis.
5. The rod bar shown has steel, brass, and aluminum sections. Axial loads are applied at cross sections A, B, C and D. The allowable stresses are 125 MPa in steel, 70 MPa in the brass, and 85 MPa in the aluminum. Assume that the allowable stresses are the same for tension (T) and compression (C). (a) Determine the diameter required for the brass bar. (b) Determine the required diameter for the steel bar. (c) Determine the required diameter for the aluminum bar. Express your answer in millimeters. Steel Brass C Aluminum B A 100 kN 85 kN 200 kN 215 kN 0.5 m 0.5 m 0.5 m
The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec =23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f' = 25MPa 800 IDE 730 N12 ligs (fsv.f-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Calculate the combination load for the reinforcement concrete beam shown in Figure 3. Unit: KN/m with two decimal. 1.2G+1.5Q=w
Connections Example: Calculate the strength of the single lap joint. The plates are made of 1"x4" wooden blocks with a 2" overlap. The glue can carry 125 psi in shear. The wood can carry an axial stress of 1000 psi. How much force P can the joint carry? Sketch and FBD P b a P
Determine the shear Load that act on the fillet weld that joining two plates together if the working stress is 11300 Ib/in? Throat
The two steel plates are bolted to the wooden beam shown by 30-mm-diameter bolts spaced at 200 mm. Knowing that beam is subjected to V 5000 N, and that the moduli of elasticity for steel and wood are 200 and 40 GPa, respectively. Determine: (a) Shearing stress in each bolt; and (b) shearing stress at the mid- height of the upper steel plate. 150 mm 12 mm 250 mm 12 mm Solution:-
The plate welded to the end of the I-beam is fastened to the support with four 10-mm-diameter bolts (two on each side). Assuming that the load is equally divide among the bolts, determine the normal and shear stresses in a bolt. Express your answer in MPa.
A beam cast monolithically has the following properties: bf=1200mm, t or hf = 110mm, bw=380mm and h=800mm. It is reinforced with 10D32mm grade 420MPa bars. Concrete strength is assumed to be 27.5MPa and the centroid of tension reinforcement is located 665mm from the outermost compression fiber. A. Determine maximum nominal moment to ensure tension controlled, kN-m. B. Calculate the balanced steel area, mm2. C. Calculate the balanced moment in kN-m.
a) For the rectangular section shown below the maximum allowable tensile stress in the concrete Fct = 3MPa. Assume an uncracked section and find the maximum moment the section can resist as well as the stress in the reinforcement for this moment Ec:= 30-GPa Es:= 200 GPa b:= 300 mm h := 520 mm d:= 460 mm 2 As 1470 mm := b As