QUESTION 3 Rod ABCD is connected to Rod DEFG at D and is also connected by rod BF by pins. A pulley is connected to end G with radius of 0.1m. The rope is hanging around the pulley to hold a mass M1 of 100 kg. The other end of the rope is connected to point C at rod ABCD. Another rod EH is also connected to point E by pin to hold the structure. Point A and point H are also by pin connections to the wall. Points A, B, C, D, H are vertically in-line. Find reactions at pins H and A. (AB = 0.2m, BC = 0.2m, CD = 0.1m, DE = 0.3m, EF = 0.15m, FG = 0.15m, EH = 0.5m, the mass of the rods are neglected). 0.2m 0.2m Radius Pulley G- 0.Im 0.Im 0.15 0.3m E 0.15 0.5m MI - 100 kg H

QUESTION 3 Rod ABCD is connected to Rod DEFG at D and is also connected by rod BF by pins. A pulley is connected to end G with radius of 0.1m. The rope is hanging around the pulley to hold a mass M1 of 100 kg. The other end of the rope is connected to point C at rod ABCD. Another rod EH is also connected to point E by pin to hold the structure. Point A and point H are also by pin connections to the wall. Points A, B, C, D, H are vertically in-line. Find reactions at pins H and A. (AB = 0.2m, BC = 0.2m, CD = 0.1m, DE = 0.3m, EF = 0.15m, FG = 0.15m, EH = 0.5m, the mass of the rods are neglected). 0.2m 0.2m Radius Pulley G- 0.Im 0.Im 0.15 0.3m E 0.15 0.5m MI - 100 kg H

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.42P: The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a...

See similar textbooks

Similar questions

The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The linkage is made of two homogenous bars of weights shown in the figure. Determine the horizontal force P required to hold the linkage in the position shown.
The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces are applied to the handgrips. (Hint: The horizontal components of pin forces at B and D are zero due to symmetry.)
W2 acts at the center G of the bar. Find the cables' tensions and the reactions at ball and socket O. W1 is 515 N. W2 is 190 N.
Solve with complete Free Body Diagram.
Solve with free body diagram.
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
L from Pivot 1. A uniform bar with mass M =3.25 kilograms is the top end of the bar. A cable connects to the bar as shown in the diagram. the 75.0 40.0° a. Calculate the tension in the cable required to keep tne bar in static equilibrium. Pivot preso your your answe stem right when n terr b. Calculate the force (both magnitude and direction) exerted by the pivot.
For the pin-connected frame shown, a = 10 in, b = 7.5 in, and F = 100 lb. Find the magnitude of the support reaction at Point A.
The radius of pulleys C and B are 125mm and 250mm,respectively. Given that TB=T'B=90kN and TC=T'C=150kN, find the reactions of supports A and D.
4 kN 3 m 4 m Use the method of joints to find all reaction and member forces in the trusses.
Crank connecting rod in Figure-1crank and connecting rods in the mechanismare the same length; AB = BC = L andBF=FC. One end to point B, the otherfrictionless with the tip horizontally.connected to movable point Dthe stiffness of the spring is k (N/m) when =90the spring is not elongated. spring mechanismforce, R1 and R2 forces and Mstatic under the influence of momentis in balance. The principle of virtual worksstatic balance of the mechanism by applyinggiving the theta angle corresponding to the positionget a relation andthe last of your student number from the table.appropriate values according to the numberCalculate the theta angle using M= -400Nm R1=300N R2=200N L=1,3m k=500N/m