Answered: Question 1 b Find the length of valley…

Question 1 b Find the length of valley curve provided on the basis of comfort condition (given that-gradient is 0.04 and speed is 70kmph). m.

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter15: Geometric Design Of Highway Facilities

Section: Chapter Questions

Problem 21P

See similar textbooks

Related questions

Q: A welded bracket connection is shown in figure. It supports a factored load of 150 kN at a distance…

Q: The speed of the brake drum shown is controlled by a belt attached to the control bar AD. A force P…

A: We have to fnd out the magnitude of the couple being applied to the drum.

Q: A fixed beam of constant section carries a load transferred from a rigid bracket as shown in figure.…

A: Given Data Find the bending moment and reaction at the fixed support and draw shear force and…

Q: The radius of the planet Venus is 3800 miles. The acceleration of gravity at the surface of the…

Q: The city of Chicago is an amazing outdoor museum of modern architecture. Pick one building from…

A: The city of Chicago is an amazing outdoor museum of modern architecture.

Q: Oil flows through a 200 mm diameter horizontal cast iron pipe (friction factor f = 0.0225) of length…

A: Given data- Diameter D=200 mm =0.2 m, Friction factor f=0.0225, Length L=500 m, Flow Q=0.32 m3/s,…

Q: Design the simple supported T-Beam section shown in fig. f'c-20 Mpa, fy=400 Mpa. Moment applied =…

Q: 1. The rock-filled concrete multi-purpose dam was built for the use on water supply, irrigation, and…

Q: Calculate shear force and draw SFD and BMD using Moment Distribution Method

Q: A bent rod ABC is supported by a pin and bracket at A and a cable CD. The weight of the bent rod is…

A: Given data in question Load 15 N/m Span 0.8 m and 1.5 m To find out Tension in cable CD

Q: A W24x62 beam (Cb = 1) spans 24 ft and is braced at the ends and middle. Determine Mn.

A: Answer From table AISC 1-1. W shape properties we have for W 24 x 62 Zx = 153 mm3 Sx = 131 mm3…

Q: : The T- beams sections shown in the figures below. f'c-28 Mpa, fy-420 Mpa. Calculate the design…

Q: I The force on the 12mm thick link in the figure shown is 2960 N. If the pin has a diameter of…

A: Given, Thickness = 12 mm Force = 2960 N Diameter of pin = 10 mm

Q: pression reinforcement of 2022mm. Calculate the design moment strength

Q: (A) 62.5 MPa (B) 31.25 MPa 125 MPa -IN A load P is supported as shown by a steel pin that has been…

A: Given :short wooden member Tensile Stress in wood= 60Mpa Shear stress in wood=7.5Mpa Allowable…

Q: 4m 1.2m/s 6m 3m 2.3m/s 9m (a) Find the area of each subsection (b) Find the discharge of each…

A: Data given Find:

Q: Solve the problem below. Provide a clean solution. Label each points from A to E then draw the load,…

Q: Determine the reactions at the support A, B and C using force method. El is constant. 12ft BO Note:…

A: Given: To find: Reactions at supports A, B, and C using the Force method.

Q: A 100-ft-thick, unconfined aquifer is penetrated by a 10-in. diameter well that pumps at a rate of…

Q: A P Front view 160 mm What is the stress in bar BD if P = 4 kips? B D 18 m 120 m

Q: 1. You are given data from a irrigation water well as: 12mM Ca, 6mM Mg, & 25mM Na. This well is to…

A: Given: Ca = 12mM Mg = 6mM Na = 25mM conductivity, ECiw = 1.5mS/cm.

Q: Using the Portal Method, determine the reaction forces for the building frame below. Draw the…

A: To determine:BMD for all columns and girders

Q: 10 Find Pressure / Force ↓ ↑ d

A: A linear momentum problem is given which has the flow rate as Q and the diameter given as d. The…

Q: The vertical stress at some depth below the corner of a 2 m x 3 m rectangular footing due to a…

A: Given Data Stress at corner of 2m × 3m footing at certain depth = 100 KN/m2 Find the stress at the…

Q: REACTIONS

Q: Q3/ For the land shown below, if the length of squares is (20m) and the scale is (1:500). Find: 0 1-…

A: using approximation interpolation method

Q: Can you list the benefits of good building design? Let's examine a project and compare its potential…

Q: - The water velocity near the river surface is 6 ft/s, and the pipe inlet is placed in th al to the…

Q: AT section has the dimensions given in Fig. ..Show that the neutral axis is 3 inches below the top…

A: Given data : INA = 166.7 in.4 Tensile stress at the bottom of the flange = 1000 psi This is a…

Q: 15.1 Refer to the infinite slope shown in Figure 15.47. Given: ß = 25°, y = 17.8 kN/m³, ' = 28°, and…

Q: Question 6 6. To find the distance across a small lake, a surveyor has taken the measurements as…

Q: |0 AMPAD use slope deflection method to analyse the beam below A 14 A = 2T 4m *4 20 kN/m A= 1.SI 4m…

A: Given Data Analyse the beam using slope deflection method. Note: As per our guidelines we are…

Q: Assignment-1; Water fills the vessels shown in the figure below. Specific gravity of manometric…

Q: 1. Using Terzaghi's Bearing Capacity Equation, determine the soil allowable bearing capacity of a…

Q: 26° and : A 6.0 m high retaining wall is to support a soil with unit weight 17.4 kN/m³, p= C=14.36…

Q: Determine the x-andy-coordinates of the centroid of the shaded area. 12 Answers: (X.)-( -13- Jin

Q: A simply supported beam having a span of 10m. carries a uniform load of 20 KN/m over its entire…

A: Given: L = 10 m UDL = 20 kN/m Point load = 40 kN at mid-span: fb= 0.6 fy fy = 200 MPa

Q: depth of 56 cm and an average velocity of 9 m/s undergoes a hydraulic jump. Determine the head loss…

Q: Why is breaking stress plotted in the stress-strain di force is increasing? A B C Due to Hooke's law…

Q: A town with a population of 150000 people is supplied with water through a pipeline from a reservoir…

Q: Determine the force in members DE, JE, and JI of the truss which serves to support the deck of a…

Q: 1. Determine the maximum value of P that can be applied without causing the crate to slip on the…

A: Given data in question Angle 50° Height 0.45 m Width 0.75 m Mass 50 kg Non sliding and sliding…

Q: - The base of the foundation sits on a normally consolidated clay dep-

Q: Sugarcane (root zone depth= 1.8m) is grown in a particular field area where GWT is 2m below surface.…

A: Step-1 According to Given Data Sugarcane (root zone depth= 1.8m) is grown in a particular field…

Q: A (A) 9 (B) 10 C) 14 (D) 13 ←N→ B 40 kips 1.5" 40 kips с -22 kips 22 kips D 20 kips From the figure,…

Q: The diameter of droplet is 0.075 mm. What is the intensity of the pressure (N/sq. cm) developed in…

A: Given data- Diameter of the droplet d=0.075 mm, Surface tension σ=0.000075 N/mm, To Find- The…

Q: For the retaining wall shown in the figure, compute the factors of safety against overturning and…

Q: Q- For a culturable command area of 1000 hectares with intensity of irrigation of 70%, the duty on…

A: Given- CCA=1000 ha, Intensity of irrigation I=70%, Duty D=1500 ha/cumec, Losses=25%,

Q: 17.4 A W410 X 100 structural steel wide-flange section is used as a horizontal lower chord member of…

A: We have to deterime the maximum and minimum combined stresses due to the direct axial load and the…

Q: Question 8 In a two-dimensional field the velocity of fluid flow is given by v = (y³ - 5x²y)i +…

Concept explainers

Control Survey and Geodetic reductions

Control surveys or survey controls are used to establish reference points as a basis for various construction activities. Vertical and horizontal control points are to be established in a control survey to increase accuracy. After establishing the control points, all other types of surveys such as topographic, right-of-way, aerial mapping, construction layout, boundary surveys, and utility mapping can be worked upon so that control networks can be formed. The place from which the observations are made is called a survey station.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 6° curve branches off from a 3º main curve in opposite direction in the layout of a BG yard. If the speed on the branch line is limited to 35 km per hour, determine the maximum permissible speed on the main line using both Cant formula and Railway Board formula. [Consider, G= 1.676 m]
Q1. A rising gradient AB and a falling gradient BC are to be connected by a vertical curve. Based on the data given in Table Q1, design the curve at 20 metres intervals. First Grade (± %) Second Grade (± %) Sighting Distance (SSD) Driver's eye (h₂) Object height (h₂) 3.6 -1.7 150 1.05 0.3 Table Q1 (Units are in metres) RL of highest/lowest pt Chainage of highest/lowest pt 38.788 3621.191
(ii) Determine the transition length based on permissible speed for a 2° curve with maximum permissible speed of 100 kmph on a BG railway track. [Consider, G = 1.676 m]
A spiral 80m long connects a tangent with a 7° 30' circular curve. If the stationing of the T.S. is 10+000, and the gauge of the tract on the curve is 1.5m. Determine the following: (a) the elevation of the outer rail at the midpoint, if the velocity of the fastest train that can pass over the curve is 60kph, (b) the spiral angle at the first quarter point, (c) the deflection angle at the end point, and (d) the offset from the tangent at the second quarter point.
Question 4 Topic: Gradients and Grade compensation- What is equilibrium cant required on a 5° curve on a BG track for the train speed of 60kmph?
Determine the cant to be provided on a BG track of 3 ° curve if the speed of several trains is as follows Number of vehicle 8 10 23 11 13 Speed (kmph) 40 50 60 70
A rising gradient AB and a falling gradient BC are to be connected by a vertical curve. Based on the data given in Table Q1, design the curve at 20 metres intervals. Table Q1 (Units are in metres) First Grade (± %) Second Grade (+ %) Sighting Distance (SSD) Driver's eye (h₁) Object height (h₂) 4.2 -1.8 145 1.05 0.3 F G RL of highest/lowest pt Chainage of highest/lowest pt| H 39.171 4048.600 K
Q1) The project speed is 100 km/h on a divided state road with a vertical curve. The driver's transition reaction time is 2.0 seconds; the friction coefficient is 0.4. Accordingly, calculate the following: a) The slopes of and g2. b) The vertical curve length (L). c) Calculate the grade line elevation of the points T1 and T2 as well every 30 meters and present them in a table format. T1 A Station 0+000 Elevation = 400 m Station 1+200 Elevation 460 m P T2 B Station 2+200 Elevation 490 m
A spiral 80m long connects a tangent with a 7° 30' circular curve. If the stationing of the T.S. is 12+000,and the gauge of the tract on the curve is 1.5m.Determine the following:(a) the elevation of the outer rail at the midpoint, if the velocity of the fastest train that can pass over thecurve is 60kph,(b) the spiral angle at the first quarter point,(c) the deflection angle at the end point, and(d) the offset from the tangent at the second quarter point.
2.) A 9% grade meets a 5% grade at station 2 + 270 of elevation 150 m. The lengths are L1 = 80 m. and L2 = 60 m. Calculate the elevation at PC, PT and at every full station.
E. A spiral 80m long connects a tangent with a 7° 30' circular curve. If the stationing of the T.S. is 10+000, and the gauge of the tract on the curve is 1.5m. Determine the following: (a) the elevation of the outer rail at the midpoint, if the velocity of the fastest train that can pass over the curve is 60kph = (b) the spiral angle at the first quarter point = (c) the deflection angle at the end point = (d) the offset from the tangent at the second quarter point =
The reduced level at the intersection of a rising gradient of 2% and a falling gradient of -3%on a proposed road is 89.05m. Given that K value is 55. The throught chainage of theintersection point is 4330m and proposed vertical curve is to have equal tangent, calculate:a) The throught chainage of the points of the vertical curve if the minimum requiredlength is to be used (LV) and the vertical curve setting out data at 20 metres exactinterval.b) The chainage and reduced level of the highest point on the curve.c) Through chainage at highest point was located exactly under a bridge, if the RL of soffit is 92.90m, calculate the headroom based on proposed vertical curve design.