Q2/ The six cylinder of a single- acting, two-stroke cycle Diesel engine are pitched 1 m apart and the cranks are spaced at 60° intervals. The crank length is 300 mm and the ratio of connecting rod to crank is 4.5. The reciprocating mass per line is 1.35 Mg. The speed is 200 rev/min. Show with regard to primary and secondary balance, that the firing order 1-5-3-6-2-4 gives unbalance in primary moment only, and the order 1-4-5-2-3-6 gives secondary moment unbalance only. Compare the maximum values of these moments, evaluating with respect to the central plane of the engine.

Q2/ The six cylinder of a single- acting, two-stroke cycle Diesel engine are pitched 1 m apart and the cranks are spaced at 60° intervals. The crank length is 300 mm and the ratio of connecting rod to crank is 4.5. The reciprocating mass per line is 1.35 Mg. The speed is 200 rev/min. Show with regard to primary and secondary balance, that the firing order 1-5-3-6-2-4 gives unbalance in primary moment only, and the order 1-4-5-2-3-6 gives secondary moment unbalance only. Compare the maximum values of these moments, evaluating with respect to the central plane of the engine.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the average piston velocity (between limiting positions) for an in-line slider-crank mechanism. The crank length is 2inch, and the crank rotates at 3000rev/min.
Match the items in columnsI and II. Column I P. Addendum Q. Instantaneous center of velocity R. Section modulus S. Prime circle Column II 1. Cam 2. Beam 3. Linkage 4. Gear (a) P-4, Q-2, R-3, S-1 (b) P-4, Q-3, R-2, S-1 (c) P-3, Q-2, R-1, S-4 (d) P-3, Q-4, R-1, S-2
A mono-cylinder engine has r = 0.3 m, l = 0.9 m, It has: crank mass m2 = 4.5 kg , crank rG2 = 0.4r, conrod mass m3 = 12 kg ,conrod rG3 = 0.3l from A, and piston m4 = 5 kg. The crank is rotating at constant speed ω =3000 rpm. The following equation is an approximation of the gas force over 180° of crank angle with Fgmax = 3000 N and β = 15º. we need to find the gas force, gas torque, and inertia force . Use approximate expressions in your calculation
2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm y 750 B 200 Z2=38 Z₁ = 19 X
QUESTION 7 A motor-cycle engine crankshaft has an angular velocity of 523.6 rad/s and is in third gear of ratio 1.62:1. The final chain reduction is 4.7:1 and the effective wheel diameter 0.73 m. Calculate the road speed of the machine in km/h.
The equation of the turning moment diagram for the three crank engine is given by: T(N.m) =25000 - 7500 sin 3theta where θ radians is the crank angle from inner dead cen?tre. The moment of inertia of the flywheel is 400 kg-m2 and the mean engine speed is 300 r.p.m. Calculate the power of the engine and the total percentage fluctuation of speed of the flywheel, if 1. The resisting torque is constant, and 2. The resisting torque is (25 000 + 3600 sin θ ) N-m.
Seatwork No. 1 An SI I-2 square engine operates on a 2-stroke cycle at 2400 rpm. The average piston speed is 15 m/se and the no. of piston action is 2. When the piston is at its maximum position the remainder volume is 0.005 Liters. Determine: a. Volumetric displacement per unit time for all cylinders (m³/sec) b. Compression ratio c. Volume at Bottom Dead Center (m³)
For the Finishing Mill of a hot strip mill, the input shaft of several different gearboxes are each driven by a DC motor of 10,500 HP operating at 125 RPM. For your ASSIGNED gearbox only, you are required to analyze the gearbox capabilities by doing thefollowing: 1. Calculate the maximum motor torque2. calculate the force transmitted by the gearing.3. Using statics, calculate the equivalent radial load at the bearings for BOTH the pinion shaft and the gear shaft. (Four bearings total; two per shaft). Include FBDs of the shafts.4. Research the load capacities for the bearings.(Hint: the bearing manufacturer is most likely Timken / Torrington).5. Calculate the expected bearing life for each bearing.6. Calculate the safety factor for both the bending strength and the pitting resistance for the pinion shaft AND the gear shaft gear teeth based on the transmitted load and the gear material(s).7. Draw the shear, bending moment, and torque diagrams for the GEAR SHAFT ONLY.8. Calculate the…
Figure Q4 shows a Mach trim system from a 737-800. It consists of a hydraulic motor driving gear A which drives gear B. Gear B is directly connected to the horizontal stabiliser via rack and pinion as depicted below. Gear A has a mass of 6kg, a radius of gyration of KGA = 0.1235m and an angular acceleration of 20kg, and a radius of gyration of Ö = 0.2t rad/s². Gear B has a mass of m = m = = 0.5341m. If the system starts from rest, determine the following when t = 3s: KGb a) The velocity of the gear rack. b) The distance the rack has travelled. c) If there is a contact force between the rack and gear B of 50N, determine the contact force between Gear A and B. d) The applied torque from the hydraulic motor. 100mm 500mm B 200mm Figure Q4-Mach Trim System tastes ins
What is the power (?) lost to main crankshaft friction in a four-cylinder engine with a 100mmbore and stroke if the engine is operating at 1500 rpm? Assume the main crankshafthas five bearings, each with a diameter of 50 mm and length of 25 mm.
7. A single cylinder, single acting, four stroke cycle gas engine develops 20 kW at 250 r.p.m. The work done by the gases during the expansion stroke is 3 times the work done on the gases during the compression stroke. The work done on the suction and exhaust strokes may be neglected. If the flywheel has a mass of 1.5 tonnes and has a radius of gyration of 0.6m, find the cyclic fluctuation of energy and the coefficient of fluctuation of speed.
A belt conveyor transports 18 tonnes per hr at 20°. Determine the unit weight of belt material in kg/ply-cm width-m to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.