Q1 Analyse the circuit shown in Figure Q1, (a) Name the function of each Op-Amp, A1, A2, A3, and A4 (b) (i) Determine the output for each Op-Amp (Vo1, Vo2, Vo3 and Vo4). RI R2 -Wir 10kN 56KN |+15V R3 R4 -Wr 10KN Al O Vo2 Vi O 1.15V 68k2 |-15V 0.3 sin ot V |+15V 1 Hz +15v Vo3 33µF |+15V Vo4 A2 Rs I-15V A3 100kN A4 -15V I-15V Figure Q1

Q1 Analyse the circuit shown in Figure Q1, (a) Name the function of each Op-Amp, A1, A2, A3, and A4 (b) (i) Determine the output for each Op-Amp (Vo1, Vo2, Vo3 and Vo4). RI R2 -Wir 10kN 56KN |+15V R3 R4 -Wr 10KN Al O Vo2 Vi O 1.15V 68k2 |-15V 0.3 sin ot V |+15V 1 Hz +15v Vo3 33µF |+15V Vo4 A2 Rs I-15V A3 100kN A4 -15V I-15V Figure Q1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
10 V(p-p),1KHz sinusoidal voltage is applied to op-amp input and non-inverting input isgrounded. What is the gain of this op-amp and why?
Q1 Analyse the circuit shown in Figure Q1, (a) Name the function of each Op-Amp, A1, A2, A3, and A4 (b) (i) Determine the output for each Op-Amp (Vo1, Vo2, Vo3 and Vo4). (ii) Draw all the waveforms based on the answer in part Q1(b)(1). R1 R2 O Vo1 10k2 56kN |+15V R3 R4 A1 -O Vo2 Vi + 0.3 sin ot V 10k2 68kN |-15V C |+15V +15V Vo3 RS 1 Hz A2 33µF АЗ |+15V Vo4 -15V 100k2 A4 -15V 1-15v I-15V Figure Q1 + +
1- Mention any two non linear applications of op- amp. 2- For the circuit given below : Vin is a sine wave Vinpp=9 V and Vref=2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vo Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
A differential op-amp circuit as shown below is used to implement a given linear voltage measuring functionV = f(V,). ouf Provide answers to questions 19 – 22. ww V. V; W R out R2 Ground
Note: assume ideal op-amp behaviors for Problems 1-4.
For the op-amp shown in the following figure, the purpose of R1 and R2 is- R2 R1 Select one: O a. to set input impedance O b. to set input impedance and voltage gain O c for bias current compensation O d. for input offset voltage compensation.
Figure Q2(a) shows an amplifier system with the given input voltagewaveform Vin and the corresponding output voltage waveform Vout. Predict what will happen to the output voltage waveform if the op-ampis given a voltage supply of VCC = +14 V and VEE = -14 V.
(c) (d) Figure Figure Q1b shows an Op-amp with a bias current compensating resistor (Rp). R₁ V₂. Vp IB. R₂ W A • V₂ Figure Olb (i) Derive an expression for V. to quantify the effect of bias currents IB+ and IB-. [3] (ii) Explain how you would choose a value for Rp to reduce the output error due to the bias currents, IB+ and IB.. [3] Referring to an op-amp define what is meant by common-mode rejection ratio (CMRR) and explain the effect a finite CMRR would have on high-precision applications. [4] Page 2 of 7 Continued overleaf
The operational amplifier (op-amp) in Figure 1 is an ideal op-amp with maximum output voltage, vO(max) is +12 V and the minimum output voltage, vO(min) is -12 V. A sine wave with ±5V peak-to-peak voltage is applied as the input, vin as shown. For each of the following conditions, derive or explain the relationship between output voltage, vo and input voltage, vin, and then draw the input and output voltage waveforms on same graph. Label the x-axis, y-axis, peak voltages and units. 1.R1 = R2 = R3 = 10 kΩ and RF = 3R1. 2.R2 = R3 = 10 kΩ, RF = 3R2 and R1 is broken (open circuit). 3.R1 = R2 = R3 = 10 kΩ and RF is broken (open circuit). 4.R1 = R2 = 10 kΩ, RF = 3R1, R3 is broken (open circuit) and the op-amp’sinverting and non-inverting terminals are accidently interchanged where node ‘x’ is connected to the non-inverting input while node ‘y’ is connected to the inverting input of the op-amp.
What must the voltage at the inverting input of the op-amp be? What is the voltage drop across Rin? What is the input current, iin, through Rin? What is the output voltage vout?
Q3. This question is on op-amps. (a) Comment on the differences between the values in the two columns of properties in the table for both an ideal op-amp and a typical 741 op-amp. Fill in the two missing values. Op-amp Gain Input resistance Unity Bandwidth Short circuit current Output resistance Ideal Infinite Infinite Infinite 0 741 200000 1MHz 25mA 75 ohms