Q.) A Wheatstone bridge strain gage, shown in figure 1, with a gage factor (F) of two is used to monitor axial strain in an old train rail. The maximum axial strain is expected to be 200 x 10-S. The output voltage of the bridge is connected to an instrumentation amplifier before interfacing it with 12 V analog to digital converter. Design a suitable instrumentation amplifier circuit which allows utilization of the full span of the ADC. Vsupoly 350 2 1 KN Vo 5V Instrum Vout Dout 350 N VB ADC 1 KN op Amp kigure Gage

Q.) A Wheatstone bridge strain gage, shown in figure 1, with a gage factor (F) of two is used to monitor axial strain in an old train rail. The maximum axial strain is expected to be 200 x 10-S. The output voltage of the bridge is connected to an instrumentation amplifier before interfacing it with 12 V analog to digital converter. Design a suitable instrumentation amplifier circuit which allows utilization of the full span of the ADC. Vsupoly 350 2 1 KN Vo 5V Instrum Vout Dout 350 N VB ADC 1 KN op Amp kigure Gage

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. Line Regulation is determined by: a. Load current b. Changes in the load resistance and output voltage C. Changes in output and input voltage below deta
Q3. Design a DC/DC buck converter (as shown in Figure Q3) for an input voltage of 12V and an output of 5V at 20A. Assume a switching frequency of 10kHz. Constrain the inductor ripple current to be 10% of the input current and limit the output voltage ripple to 50mVp-p. a) Explain the working mechanism of the converter by sketching equivalent circuit diagrams when the switch Q is ON and OFF, Calculate the duty cycle of the switch. Find the ripple of the inductor current. Calculate the required inductance and capacitance. Sketch the waveform of the output voltage. Is the converter works at continuous conduction mode CCM? If so, give proof of that b) c) d) e) f) g) If the load current varies between 0 and 2A, what is the value of the duty cycle range and at what operating condition? DA L C² Figure Q3 DC/DC buck converter. R
What is an A/D converter with Voltage-to-Frequency Conversion (VFC)? What is the working principle?
Consider a buck converter with the controlled switch as MOSFET and the uncontrolled switch as diode, the input to buck converter is 60 V. The MOSFET is turned on and off for 20 msec and 10 msec periodically. Assuming ideal components, the output voltage of the buck converter is
In Steady-State Operation o f Buck DC-DC Converter Explain how the switching frequency component is eliminated by the output filter network.
A signal generator having a source resistance of 50 2 is set to generate a 1 kHz sinewave. Open circuit terminal voltage is 10 V peak-to-peak. Connecting a capacitor. across the terminals reduces the voltage to 8 V peak-to-peak. The value of this capacitor is -HF. (Round off to 2 decimal places).
Draw the circuit diagram of a 3 bit R - 2R ladder Digital to Analog Converter. Compute the output of the circuit above for a digital input of (110)2. State one disadvantage of this circuit.
Calculate the output impedance for small-signal equivalent circuit. (R=10 k2, r. =10 k2) ER Rout O A) Rout = 3.3 ka O B) Rout = 20 ko )C) Rout = 30 ka DI Rout = 5 k0
8- Auto transformer is used in tuned amplifier to (transform low impedance of transistor input, match to the load, tune to operating frequency, stabilize tuned amplifier). 9- The dual slope A/D converter is popular because it is (fast converter, low power, low complexity, high resolution). 10- The most important feature of flash type A/D converter is (high resolution, fast, low component spread, low power dissipation).
A 10-Ohm fully resistive load system will be fed from a photovoltaic (PV) module. Load (converter output) voltage 12 V DC is required. But the PV output is DC 18 Volt. Buck type DC/DC converter design is required between load and PV. For this j-converter, the inductor current must be continuous and the fluctuation rate of the load voltage must be at most 0.5%. The lowest switching frequency is 40 kHz; A) What is the lowest Capacitor value (microF) that meets the design conditions for the output capacitor ? B) What is the RMS value of the inductor current (A) ? C) What is the average value of the inductor current (A) ?D) What is the inductance value (microH) that meets the design prerequisites?E) What is the lowest inductance value to be calculated (microH) ?F) What is the operating ratio of the circuit (Duty) ?
A 10-Ohm fully resistive load system will be fed from a photovoltaic (PV) module. Load (converter output) voltage 12 V DC is required. But the PV output is DC 18 Volt. Buck type DC/DC converter design is required between load and PV. For this j-converter, the inductor current must be continuous and the fluctuation rate of the load voltage must be at most 0.5%. The lowest switching frequency is 40 kHz; A) What is the lowest Capacitor value (microF) that meets the design conditions for the output capacitor ? B) What is the RMS value of the inductor current (A) ? C) What is the average value of the inductor current (A) ?D) What is the inductance value (microH) that meets the design prerequisites?E) What is the lowest inductance value to be calculated (microH) ?F) What is the operating ratio of the circuit (Duty) ? Please answer D;e;f
Calculate the total offset voltage for the circuit shown below for op-amp specification values of input offset values, VIO=2.8 mV and IIO=110 nA with RF=14000 ohm and Rin= 3000 ohm.