Propblem-11Figure below shows a CE power amplifier in which the collector resistor serves also as the load resistor.Assume ßpc = Bac = 100, Determine-+Vcc+15 Va. The de Q-point (Icq and VCEQ).b. The voltage gain and the power gain.RLS100 n0.5 W1.0 knc. The power dissipated in the transistor with no loadVind. the total power from the power supply with no load22 μFe. the signal power in the load with a 500mV inputREI*8.2 0V.500 mV pp1.0 kHz330 nRE236 N100 μF

Answered: Image /qna-images/answer/96eca881-02ad-4189-992f-f5a3cbbd7c88.jpg

Propblem-11 Figure below shows a CE power amplifier in which the collector resistor serves also as the load resistor. Assume Boc = Bac = 100, Determine- +Vcc +15 V a. The de Q-point (Icq and VCeQ). b. The voltage gain and the power gain. RL 100 n 0.5 W 1.0 kn c. The power dissipated in the transistor with no load Vin d. the total power from the power supply with no load 22 uF e. the signal power in the load with a 500mV input RE 8.20 V, S00 mV pp 1.0 kHz 330 n Rea 36N 100 µF

Propblem-11 Figure below shows a CE power amplifier in which the collector resistor serves also as the load resistor. Assume Boc = Bac = 100, Determine- +Vcc +15 V a. The de Q-point (Icq and VCeQ). b. The voltage gain and the power gain. RL 100 n 0.5 W 1.0 kn c. The power dissipated in the transistor with no load Vin d. the total power from the power supply with no load 22 uF e. the signal power in the load with a 500mV input RE 8.20 V, S00 mV pp 1.0 kHz 330 n Rea 36N 100 µF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

c. For the circuit shown in Figure, determine lc and VCB. Assume the transistor to be made of Silicon. Ic RE=1.6 kn Rc=1.1 kn EE=8 V Vcc= 20 v
Vin For the circuit shown, assume that Vo = 3V and that the transistor is described as follows: B-100, Va = 100V, VT = .025V. a) Determine the small signal parameters for the transistor. b) Draw the small signal model 5V 5V 300uA Vo www 4K 625 C
circuits by using the small signal models of the transistor. Assume the Early voltage of the transistors are infinitely large. Calculate the small-signal input and output impedances of the following Vcc R1 R1 Rout VB RE Rin R2
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
Problem5: For the common base circurt shown in figure find I. and VCB. Assume transistor is Silicon (a-0.98) Ic Rp= 1.5 ko Rc= 1.2 kn VEE = 8 V. Vcc= 18 V
A 4.7 zener diode is connected to the base resistor. The left side of the resistor sits at about 12V. The right side of the biasing resistor is connected to the Zener and npn transistor. The Zener bias is 5mA. The base current needed is 80uA. What is the appropriate resistor for this circuit? (In kohms) I
Identify the source, drain, gate, and bulk terminalsand find the current I in the transistorsAssume VTN = 0.70 V
Draw and explain the schematic diagram for the following: Common Base NPN operating in cut-off region Common Emitter PNP operating in the active region Common Collector NPN operating saturation region From the given figure, identify and explain the 1.Type of Transistor 2. Type of Configuration 3. Mode of Operation V3 SV Q2 100A/A Q3 100A/A 7 V4 5V V6 5V
Figure below shows a CE power amplifier in which the collector resistor serves also as the load resistor. Assume ßpc = Bac = 100, Determine- +Vcc +15V a. The de Q-point (Icq and VCEQ). b. The voltage gain and the power gain. RL 100n 0.5 W 1.0 kn c. The power dissipated in the transistor with no load d. the total power from the power supply with no load 22 uF e. the signal power in the load with a 500mV input Re 8.2 n 500 mV pp 1.0 kHz 330 n Rea 36 0 100 uF
1. For the circuit in Figure 1: a) Calculate the input and output power if the input signal results in a base current of 6 mA. b) Calculate the input power dissipated by the circuit if Re is changed to 2kn. c) What maximum output power can be delivered by the circuit if Rg is changed to 2 ko? d) If the circuit is biased at its center voltage and center collector operating point, what is the input power for a maximum output power of 2W? 20V Re = 16 2 1.2 ks2 B- 40 100 µF Figure 1
Q1:- find the emitter, base and collector currents and VE. (let any parameters if you need). + Vcc=6 V 2 k2 530 k2
Set up a midpoint bias for a JFET with IDSS = 14 mA and VGS(off) = -10 V. Use a 24 V dc source as the supply voltage. Show the circuit and resistor values. Indicate the value of ID. Indicate the value of VGS. Indicate the value of VDS.