Problem 2: Class E Amplifier Design A schematic of class E amplifier is shown in the figure 2 given below For optimum operation with 50% duty cycle and when the loaded quality factor QL of series fundamentally tuned resonant R-Lo-C, circuit is infinite to provide pure sinusoidal current flowing into load R a) What are the nominal voltage conditions across the switch that a class E amplifier has to satisfy b) In such conditions give the expression of i(t) and v(t) at the drain source junction c) For these waveforms, demonstrate that the loading RLC network must verify R v? R = 0.5768 d P C = 0.1836- L = 1.1525

Problem 2: Class E Amplifier Design A schematic of class E amplifier is shown in the figure 2 given below For optimum operation with 50% duty cycle and when the loaded quality factor QL of series fundamentally tuned resonant R-Lo-C, circuit is infinite to provide pure sinusoidal current flowing into load R a) What are the nominal voltage conditions across the switch that a class E amplifier has to satisfy b) In such conditions give the expression of i(t) and v(t) at the drain source junction c) For these waveforms, demonstrate that the loading RLC network must verify R v? R = 0.5768 d P C = 0.1836- L = 1.1525

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single-phase full-wave converter in the figure below is supplied with a 120-V, 60-Hz source. The load is highly inductive and the load current is continuous and free of ripples. The electromotive force is neglected (E = 0) and the resistance has a value of R = 10 2. The average output voltage is 85% of the maximum possible average output voltage. The delay angle would be equal to: Select one: 81.8° O b. 31.8° O c 67.8° O d. 51.8° AT₁ AT, R L +7=4₂ W
Part 1) Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is 0.25 ms and the duty cycle k is first set to 0.5. The load is resistive with R=10 Ohms. The critical value of L and the critical value of C are equal to: a. 0.625mH and 0.392uF b. 0.625mH and 0.196uF c. 0.312mH and 0.196uF d. None of these Part2) Now consider the same given but the load is an inductive load with R=10 Ohms and L=10 mH. The switch is ideal. Calculate The RMS load current Io and the RMS converter current Ir are equal to: Select one: a. 5A and 3.54A b. None of these c. 8A and 5.66A d. 12.5A and 8.84A
Q.) Figure below divider bras amplifier Circuit. Givent the model Parameter : gm = 5o mS emitter (CE) Voltage BJT hibrid- TT Shows a Common riT: 6 Kr and to %3D : 00 +Vc. RI C2 Tooks touf RL Vo ihe 200 RE TCE Vs 20 a Draw the Ac eQuivalent at low Freauency Circuit Zi and b.) Determine inPut impedance at mid FreaUincy OutPut imPedance Z0 c.) Calculafe two low Cut -oFF FreQuen Cies FLC1 and FLC2 Ci and E2 respectively Such as due to the exterda al capacitors
Q4: Design a buck converter to produce an output voltage of 18 V across a 10-_ load resistor. The output voltage ripple must not exceed 0.5 percent. The dc supply is 48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor and capacitor, the peak voltage rating of each device, and the rms current in the inductor and capacitor. Assume ideal components. DE
Q4: Design a buck-boost converter to provide an output voltage 12V from a source that varies 'between 10V-16V. Given the load resistor is 10 2, assuming the frequency is 50 KHz and the output voltage ripple is 1.5% Specify: a. The duty ratio. b. The value of inductor. c. The value of capacitor. Note: Determine the values of inductor and capacitor with DI only.
Write the loop equations for a Buck converter in the two modes if the inductance is characterized by a combination of inductance L1 in series with an equivalent resistance r1, filter capacitance is characterized by a capacitor C1 in series with resistance r2. Also assume that the controlled switch has a drop of 0.4V and the freewheeling diode has a voltage drop of 0.65v. Draw the corresponding equivalent circuits in each mode.
a. b. C. There is a dc-dc converter that provides isolation between input and output current. Identify the converter type and describe the operation. Draw the equivalent circuit to support the explanation. Assume the converter operates in continuous-current mode. Explain why a switched -mode dc-dc converter is better that a linear regulator. As an electrical engineer, you are required to design a chopper circuit with an output voltage of 10 V from a 30 V input with switching frequency of 50 kHz. The circuit is operated in continuous current, and output ripple voltage is less than 0.8% with resistance load of 30 Q. Assume the inductor value is 50 % larger than Lmin and assume ideal components for this design. Identify the chopper type and construct the circuit with IGBT as the power switching.
Draw the circuit diagram of DC to DC converter using switched capacitor.
A step down converter has a load resistance R-0.5Ohms, an input voltage Vs-200V and a battery voltage E-OV. The average load current la-250A and the converter frequency is 1000 Hz. The value of the inductance L that would limit the maximum load ripple current to 5% of la, would be equal to: Select one: O a. 15 mH O b. None of these O c. 4 mH O d. 9 mH
In circuit analysis, expound separately the meaning of getting negative values for the current & voltages, in theoretical calculations or experimental data? Relate to Kirchoff Rules
What is an A/D converter with Voltage-to-Frequency Conversion (VFC)? What is the working principle?
A high voltage engineer cascades 6 stages of a voltage doubler circuit to analyze effectiveness of doing so. Each capacitor in the circuit is 15 nF, of the input Asupply is 100 kv at Frequency 100 Hz. . so this voltages not enough with one moudle.So How much moudle can be in cascades fashion if the load current is 1 mA.