Problem 11.34The oil tanker has a smooth surface area of 4.3(10³) m² in contactwith the sea. The velocity of the ship is 2 m/s. Suppose that I = 320m. Take p = 1030 kg/m³ and μ = 1.14(103) N-s/m². (Figure 1)Figure2 m/s< 1 of 1 >Part ADetermine the friction drag on its hull.Express your answer to three significant figures and include the appropriate units.F =SubmitPart BW =μASubmitValueRequest AnswerDetermine the power required to overcome this force.Express your answer to three significant figures and include the appropriate units.μAValueUnitsDAMLAR Ancuar?Units?

Answered: Image /qna-images/answer/46f94f4f-b85f-495e-8c86-936478aab541.jpg

oblem 11.34 The oil tanker has a smooth surface area of 4.3(103) m² in contact with the sea. The velocity of the ship is 2 m/s. Suppose that L = 320 m. Take p = 1030 kg/m³ and μ = 1.14(10-3) N -s/m². (Figure 1) gure 2 m/s 1 of 1 ▾ Part A Determine the friction drag on its hull. Express your answer to three significa F = Value Submit Request Answer ▾ Part B μÀ W: = Determine the power required to overcom Express your answer to three significa μA C Value Un UP

oblem 11.34 The oil tanker has a smooth surface area of 4.3(103) m² in contact with the sea. The velocity of the ship is 2 m/s. Suppose that L = 320 m. Take p = 1030 kg/m³ and μ = 1.14(10-3) N -s/m². (Figure 1) gure 2 m/s 1 of 1 ▾ Part A Determine the friction drag on its hull. Express your answer to three significa F = Value Submit Request Answer ▾ Part B μÀ W: = Determine the power required to overcom Express your answer to three significa μA C Value Un UP

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 250 kg crate is subjected to forces F1=790N and F2=1300N. The coefficient of kinetic friction between the crate and the surface is 0.23. Assume angle 1 = 38 degrees and angle 2 = 15 degrees. a. determine the normal force developed between the crate and the surface. b. if the crate is originally at rest, determine the distance it slides in order to attain a velocity of 8.5m/s.
Determine the speed and torque required to drive an agitator of 675 mm diameter rotating in air if similar agitator of diameter 225 mm, rotating at 23 rev/s in water requires a torque of 1.1 Nm. Given Pair = 1.23 kg/m³, Pwater = 1000 kg/m³, Mair = 1.86 x 10-5 Pa-s, Pwater = 1.1 x 10-3 Pa-s. Obtain your result after arriving at the relevant group of dimensionless terms and the corresponding similarity law, considering that power required as a function of the speed, diameter of agitator, the fluid density and viscosity of fluid in which agitator rotates.
Q5. A brass cube “R” inch on a side weighs (Rx10)lb.Hold this cube in equilibrium underwater by attaching light foam buoy to it. If the unit weight of foam is 4.5 lb/ft3, calculate the minimum required volume of the buoy? (where R is 32)?
Mass of crate: 100 kg μk 0.25 Determine the speed of the crate when x = 1.5 m. k = 2 kN/m 10 m 45°
Block A has a mass of 100 kg and the coefficient of friction is 0.20. Determine the friction force between A and B. 500 N 1 90° Bed A 30° 450 N B Dreble m .
The 80-kg crate is subjected to the forces shown. If it is originally at rest, determine the distance it slides in order to attain a speed of v = 7 m/s. The coefficient of kinetic friction between the crate and the surface is uk %3D = 0.27. Forces with respect to 45° and 30° are 613 N and 368 N, respectively. %3D |30° 45°
3/1 The 50-kg crate is projected along the floor with an initial speed of 7 m/s at x = 0. The coefficient of ki- netic friction is 0.40. Calculate the time required for the crate to come to rest and the corresponding dis- tance x traveled. Vo = 7 m/s 50 kg H₂=0.40 Hx Problem 3/1
A piece of material experiences a unknown distributed load of snow along its entire surface area of 1650 fr . The snow loading is 0.350ft tall across the entire surface, along a 90ft long surface. The surface has an uneven width as shown in the diagram. Treating the snow to have the same properties of water, determine the magnitude of the resultant force that the snow exerts on the material (hint: an integral will be necessary). 0.350FE 30FE 2 1650FE 90Ft
E. The weights of Crates A and B are 150 lb and 50 lb, respectively. Determine their speed when they begin from a standstill. Also, calculate the force that crate A exerted on crate B throughout the move. Hk = 0.24 is the coefficient of kinetic friction between the containers and the ground. P 75 lb A
If the specific gravity of the oil SG-0.8 what should be the value of h so that the net horizontal hydrostatic force on the cylinder with diameter of D be equal to zero? D/2 water D a) h=0.75D b) h=1.25D 9h-1.5D d)h = 1.667D h-? oil
A 400 lb block is resting on a rough horizontal surface for which the coefficient of friction is 0.40. Determine the force P required to cause motion to impend if applied the block (i) horizontally or (ii) downward at 30 degrees with the horizontal.=(iii) What is the minimum force is required to start themotion. *No figure
The crate in an inclined plane (angle of inclination, 02=10°), has a mass M=200 kg and is subjected to a towing force P acting at an angle e1=20° with the horizontal. If the coefficient of static friction is 0.2, determine the magnitude of P to just start the crate moving down the plane. (A) N=1909 N, P=47 N (B) N=1687 N, P=39 N N=1658 N, P=37 N N=1780 N, P=52 N