For the Graph shown below of the Load-Line Curveof a Class A Power Amplifier, if the voltage Vcc = 30(V), andRc = 50 (N)IcVccRcIBVccVCEa) The Value of (Ic Dc) that results to Maximum Valueof AC (lc p-p ) (in A) =(A)b) The maximum possible value of (Ic p-p ) generatedfrom the input voltage, if the DC value of (lc Dc) =0.46 A (in A) =(A)c) The maximum possible value of (Ic p-p ) generatedfrom the input voltage, if the DC value of (Ic Dc) = 0.1A (in A) =(A)

Given: The graph shows below is a load-line curve of a Class A power amplifier: Here, VCC=30 VRC=50…

For the Graph shown below of the Load-Line Curve of a Class A Power Amplifier, if the voltage Vcc = 30 (V), and Rc = 50 (2) Ic VcC Rc IB Vcc VCE a) The Value of (Ic Dc) that results to Maximum Value of AC (Ic p-p ) (in A) = (A) b) The maximum possible value of (Ic p-p ) generated from the input voltage, if the DC value of (Ic Dc) = 0.46 A (in A) = (A) c) The maximum possible value of (Ic p-p ) generated from the input voltage, if the DC value of (Ic Dc) = 0.1 A (in A) = (A)

For the Graph shown below of the Load-Line Curve of a Class A Power Amplifier, if the voltage Vcc = 30 (V), and Rc = 50 (2) Ic VcC Rc IB Vcc VCE a) The Value of (Ic Dc) that results to Maximum Value of AC (Ic p-p ) (in A) = (A) b) The maximum possible value of (Ic p-p ) generated from the input voltage, if the DC value of (Ic Dc) = 0.46 A (in A) = (A) c) The maximum possible value of (Ic p-p ) generated from the input voltage, if the DC value of (Ic Dc) = 0.1 A (in A) = (A)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q4. For the circuit shown in Figure Q4: i) What is the type of MOSFET and the amplifier configuration? ii) Find the Q-point (Ip and Vps) iii) What is the device transconductance, gm? iv) What are the voltage gain and output voltage? v) Draw the input /output voltage waveforms showing the phase relationship between them. Be sure to label them properly. +20V IDON = 15 mA@ VcsON = 6V VGSTH = 1V 1kQ Rp C2 10M2 Ro1 out Vin 3.3MQ Ra, 47003 Rs 50mV Figure Q4
The circuit diagram of step-up type DC-DC converter is given below. It is assumed that the output capacitor is large enough and the output voltage is constant. (Consider that there is no circuit losses.) Select an inductance value for the CCM operating state of the circuit. With this inductance value, taking into account the minimum input voltage and minimum output current, calculate the value of C so that the output voltage has a fluctuation of 1%.
5, a) Determine Vdsat when ID=.5 mA. b) Determine Kn when ID = 0.5 Amps. (Show your work!) c) Determine VTN. (Show your work!) d) Vgs Consider the circuit and corresponding graph, shown below. ID (mA) 0.60 0.50 0.40 0.30 0.20 0.10 0.00 0 0.5 Vds 1 1.5 2 2.5 Vds 3 3.5 4 4.5 5 -Vgs = 1V - Vgs = 1.1V - Vgs = 1.2V - Vgs = 1.3V
Figure shows a class A power amplifier circuiti Calculate IC(sat), VCE(cut−off),ICQ and VCEQ if BDC = 110 and VBE =0.7 ?, ii Based on the answer in (i), illustrate the DC load line and mark theQ-point.iii Calculate the power efficiency for the circuit in Figure
A) Design with drawing an Op-Amp series voltage regulator to give a regulated O/P voltage of 12V for an I/P of 15V B) Calculate the line regulation if the I/p increases to 4V leads to increase the O/P voltage to 0.02V.
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
4) Consider the clamping circuit below, assume Vref=3 V and Vin=5sin(wt) ..Draw the output voltage waveform. Clearly mark the max and min of the voltage.. Vref
With an aid of a. c. equivalent circuit, derive an equation representing common- mode gain (Ac) of the circuit.
Figure 1(a) shows a series fed class A amplifier circuit. In order to achieve the maximum efficiency, the Q point must be located at the center of the DC load line as shown in Figure 1(b). This generates the maximum output current swing of Icmax (p – p) RC and the maximum output voltage swing is VCEmax(p – p) = Vcc Assume that the maximum input de power is (1 Vcc Pimax(dc) = Vcc!cQ(max)=Vcc \2° Rc. 2Rc Find the maximum efficiency, 7 of this circuit.
VR2 (t) voltage will be calculated by analyzing the circuit in Figure 2 with a non-linear element using the Small Signal Analysis method. For this purposea) Find the operating point VkQ, IkQ voltage and current values of the nonlinear element.b) Linearize the non-linear element at the operating point.c) Find the voltage VR2 (t) by calculating the effect of the variable source using the linear model.
for the Steady-State Operation of Buck DC-DC Converter Describe the nature of the current through the equivalent series resistance (ESR) of the capacitor. What is the effect on the shape of the current when the value of the ESR is increased?
In this voltage divider bias circuit, the input is at the base. Output is at the emitter with a high input resistance and low output resistance. The maximum voltage gain is 1 and the coupling capacitors must have a negligible reactance at the frequency of operation. (use to answer a and b) a. Derive the expression for the voltage gain, current gain, and power gain in terms of power delivered to the load, R. b. Sketch both the DC and AC equivalent circuits. c. Derive the expression for ripple factor of Half Wave Rectification with a capacitor filter.