For the following circuit, V₁=12V, V₂=5V, C=5mF, R₁=R₂=2 №2, and R3 = 4 Q. Calculate: a. Time constant (T) b. Initial value for the capacitor voltage. c. Final value for the capacitor voltage. d. The complete solution of capacitor voltage (vc) for all t > 0. e. The energy stored in the capacitor. R₁ V₁ R3 www 1=0 + VC R₂ www V₂

For the following circuit, V₁=12V, V₂=5V, C=5mF, R₁=R₂=2 №2, and R3 = 4 Q. Calculate: a. Time constant (T) b. Initial value for the capacitor voltage. c. Final value for the capacitor voltage. d. The complete solution of capacitor voltage (vc) for all t > 0. e. The energy stored in the capacitor. R₁ V₁ R3 www 1=0 + VC R₂ www V₂

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
4. In what form is the energy of a capacitor stored?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
1. Find the voltages across the following components (a and b) after 1 second. The Capacitor is initially charged at 10V while the voltage source is 1V. Resistor R is 103 ohm while capacitor C is 1mF. a. Capacitor C b. Resistor R c. What is the best 1st order DE Method applicable to this problem?
a) With switch J2 open, close switch J1. Estimate the time it takes to do it. Obtain the equations for the voltage and current of the capacitor. Determine the energy stored by the capacitor. b) Open switch J1, close switch J2. Estimate the time it takes to do it. Obtain the equations for the voltage and current of the capacitor.
QUESTION 1 a) State two (2) main properties or acts of each capacitor and inductor in RL and RC cireuit analysis ( voltage and current ). b) Define what is capacitor and inductor. Support the answers with an appropriate illustration of capacitor and inductor basic structure. c) Natural response happens to all passive storage element component. Explain natural response for circuit behaviour for a capacitor with an appropriate illustration. d) The switch in circuit Figure 1 has been closed at t 0. 6 A 10 0 i(t) 7.5 H Figure 1: First Order RL Circuit
An inductor is "charged" to some value, then connected in series with a 1002 resistor and allowed to "discharge". A measurement of the potential difference across the resistor is shown in the figure below. Compute the time constant of the circuit, the inductance of the inductor, and the initial current through the inductor. 12 10 8 6 Potential across resistor (V) 2 0 0 0.0001 0.0002 0.0003 0.0004 0.0005 0.0006 0.0007 time (s)
The following figure represents an RC-Circuit with the switch. In Figure A, the capacitor is initially uncharged. In Figure B, the capacitor is initially fully charged. 1) Draw and label the current direction immediately after the switch is closed for each figure. 2) Consider Figure A. What is the voltage across the capacitor as t → 0? Explain. 3) Consider Figure B. Is the voltage across the resistor increasing, decreasing or staying the same as t → 0? Explain. A) B) R C
Determine the total capacitance, total charge, individual voltage drop and charges across each capacitor. Use two decimal places for your answer. Put your answer for the individual voltage and charge for each capacitor in a table for faster checking. Thank you! Here are the values for the capacitors: C1 = 55 C6 = 50 C2 = 25 C7 = 17 C3 = 49 C8 = 44 C4 = 22 C9 = 53 C5 = 45 C10 = 44
3. R1 = 6.0M2, R2 = 12.0M2, E = 12.0V. When the capacitor is completely discharged, open sl and close s2, it takes 66s to charge the capacitor to half full. Find the capacitance C. When the capacitor is completely discharged, close both switches, how long does it take to charge the capacitor to 70%? RI R2 1)
Q19. For the series-parallel inductor circuit shown in figure B19, answer the following questions. L2 2mH 4mH L3 L4 SMHS 5mH 3.5mH L6 8mH L7 2mH L3 4.5mH e Figure B19 Determine the inductance, L3 value. ii) If E is the energy stored in inductor for current, Calculate the energy if the current value is increased twice.
There is no energy stored in the circuit at the timethe current source is energized.1. a) Find Ia and Ib.2. b) Find ia and ib.3. c) Find Va, Vb, and Ic.4. d) Find va, vb, and vc.5. e) Assume a capacitor will break down whenever its terminal voltage is 1000 V. How long after the current source turns on willone of the capacitors break down?