a) A brass bar, having cross-section area of 900mm2, is subjected to axial forces asshown in figure 4.1 in which AB =0.6m, BC = 0.8m and CD = 1.0m.40 kN70 KN20 kN10 KNFigure 4.1Find the total elongation of the bar. Take E = 1 x 10$ N/mm²%3D

Answered: Image /qna-images/answer/3678ee47-84b9-4d6a-9813-6c4cd112a801.jpg

Answered: Find the total elongation of the bar.…

Engineering

Civil Engineering

Find the total elongation of the bar. Take E = 1 x 10$ N/mm²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

allowa quired wall thickness 2:11 .l 0.31 KB/S 64 Edit 16 A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E = 200 GPa. 36 mma 2 m OWhat is the displacement of the loaded end B of the bar? ® Determine the tensile stress induced in rod CD by the 80 kN load D If the allowable stress in rod CD is 124 MPa, what weight W can be safely 1.8 m 12m applied? w80 AN 1. A holl ow cir cular steel colum n is s ubjected toa compression load of 380 kN . The column has a length of 2.4 mn.and an outside dia meter of 187.5 mm. E - 200,000 MPa Determine the min. roquired wall thicknesss base on an allo wable com pressi ve stress of 48 MPa. Determine the min. required wall thickness based on 30 MPa. Determine the min. required wall thickness based on the allowable shortening of the colum n to b e 0.5 0 mm- allowable shear stress of C3D P-38 O kN 2.4 m 2. An 8 mm diameter steel rod, 20 m. long…
•213. The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before the load is applied. If the load P=50KN, determine is vertical movement. ALUMINUM L=4m A=500mm? STEEL L=3m A=300mm2 E=200GPA E=70GPa 2m 3m
. Consider the following wooden T-beam on its side. It consists of two wooden parts glued together. Assume the glue nas a perfect bond. The densities of the two wooden parts differ and are indicated on the figure. The figure is not to scale. y Pq = 900 kg/m %3D 17 mm P2 = 740 kg/m? 20 mm 150 тm Determine the a-coordinate I of the center of mass of the T-beam. 90 mm
The support in Figure 14.21a is to be constructed from a 4340 steel plate tempered at 800◦F. The yield strength of the steel is 228 ksi, and; its value of KIc is 51 ksi√ (in.). The width of the support, w, is 4 in.; the length, L, is 36 in.; and the thickness, t, is 0.25 in. Figure 14.21b gives f(a/w) in the equation σ = KIc/[f(a/w) √ (πa)]. A. If the crack length, a, is small enough, the support will yield before it fractures? What is the size of the largest crack for which this is true (i.e., what is the largest value of a for which general yielding will precede fracture)? Assume that any fracture would be in mode I (plane strain). Discuss critically the assumption of mode I. B. If it is guaranteed that there are no cracks longer than a length equal to 80% of that in Figure 14.21a, does this assure that failure will occur by yielding, rather than fracture? Explain briefly.
To lower ends of the three bars in the figure two are the same level before the rigid homogeneous W=176kN block is attached. Each still bar has a length of 1.00 m, an area 500mm² and E=200 GPa. For the bronze bar the length is 1.6m, the area is 900mm² and E= 83 GPa. What is the stress developed in the bronze bar? What is the stress developed into steel bar? What is the elongation of each bar?
The bar AB is attached to aluminum and steel rods, horizontal before the load P is applied. Find the displacement of steel rod caused by the force P = 55.25KN. ALUMINUM L= 4.552m A = 565mm2 E= 70GPA STEEL L= 3.525m A = 345mm2 E= 200GPA 3.65m 2.46m
Calculate the stresses that will occur at point A in the adjacent figure. r=10mm
Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
The bar AB is attached to aluminum and steel rods, horizontal before the load P is applied. Find the displacement of aluminum rod caused by the force P = 55.25kN. ALUMINUM L=4.25m A = 556mm2 E = 70GPA STEEL L= 3.25m A = 354mm2 E= 200GPA 3.56m 2.64m
Beam AB is made of three plates glued together and is subjected, in its plane of symmetry, to the loading shown. Knowing that the shear force is V=3.5kN and I=8.63*106 m“, determine the following: -100 mm 20 mm -Joint a 80 mm C 20 mm - 68.3 mm 20 mm 60 mm The value of Q is equal to in m3: The value of t for the Joint a is equal to in mm: The average shearing stress at Joint a is equal to in kPa:
Compute the deformation of the beam using conjugate method E= 200 GPa I= 1000 x 106 mm4
• The three steel bars shown in the figure are pin connected to a rigid member. If the applied load on the member is 15 kN, determine the force developed in each bar. Bars AB and EF each have a cross- sectional area of 50 mm2, and bar CD has a cross-sectional area of 30 mm?. Take Est = 200 GPa. B D F 0.5 m E - 0.4 m- 0.2 m 0.2 m 15 kN