Find the phase and gain margins for thefollowing feedback systemR(s)The Bode plot ofMagnitude (dB)Phase (deg)20-20-40-600-90-180-27010-²-1101s3+2s²+2.2s+0.21s³+2s²+2.2s+0.2Bode Diagram10⁰Y(s)Frequency (rad/sec)is10¹Select from(a) Gain Margin: 4.2, Phase Margin: 73.8°(b) Gain Margin: 0.24, Phase Margin: 73.8°(c) Gain Margin: 4.2, Phase Margin: -73.8°(d) Gain Margin: 0.24, Phase Margin: -73.8°(e) None of the above/Not nominally stable

The given block diagram for the feedback system is shown below.The loop-transfer function is.The…

Find the phase and gain margins for the following feedback system R(s) + The Bode plot of Magnitude (dB) Phase (deg) 20 0 -20 -40 -60 0 -90 -180 -270 102 s³+2s2+2.2s+0.2 1 s³+2s²+2.2s+0.2 Bode Diagram 10-1 Frequency (rad/sec) 10⁰ Y(s) is 10¹ Select from (a) Gain Margin: 4.2, Phase Margin: 73.8° (b) Gain Margin: 0.24, Phase Margin: 73.8° (c) Gain Margin: 4.2, Phase Margin: -73.8° (d) Gain Margin: 0.24, Phase Margin: -73.8° (e) None of the above/Not nominally stable

Find the phase and gain margins for the following feedback system R(s) + The Bode plot of Magnitude (dB) Phase (deg) 20 0 -20 -40 -60 0 -90 -180 -270 102 s³+2s2+2.2s+0.2 1 s³+2s²+2.2s+0.2 Bode Diagram 10-1 Frequency (rad/sec) 10⁰ Y(s) is 10¹ Select from (a) Gain Margin: 4.2, Phase Margin: 73.8° (b) Gain Margin: 0.24, Phase Margin: 73.8° (c) Gain Margin: 4.2, Phase Margin: -73.8° (d) Gain Margin: 0.24, Phase Margin: -73.8° (e) None of the above/Not nominally stable

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. The Bode plots for a plant G(s), used in a unity feedback system are shown in Figure 1. Find the gain margin, phase margin, zero dB frequency, 180° frequency, and the closed-loop bandwidth. 20 log M Phase (degrees) 40 20 -20 -40 -60 -80 -100 0.1 -50 -100 -150 -200 -250 -300 0.1 Frequency (rad/s) Figure 1. Frequency response for G(s) 10 10 100 100
The figure below plots the frequency response of a multi-pole amplifier. A feedback system employing this amplifier with K = 1 will be: Bode Diagram Magnitude (dB) Phase (deg) 8 0 20 40 -60 -80 -100 -90 10-1 100 10¹ Frequency (rad/s) Select one: O a stable because wax Wpx 102
Modeling: Forced Oscillations. Resonance
Using a block diagram, show how to implement the following roll-off rates using a single-pole and a two-pole with Butterworth responses. Implement these filters as low-pass. (a)-60 dB/decade (b) -100 dB/decade (c) -40 dB/decade (d) -20 dB/decade (e) -120 dB/decade
1. The term pole in filter terminology refers to (a) a high-gain op-amp (b) one complete active filter (c) a single RC circuit (d) the feedback circuit 2. A single resistor and a single capacitor can be connected to form a filter with a roll-off rate of (a) -20 dB/decade (b) -40 dB/decade (c)-6 dB/octave (d) answers (a) and (c) 3. A band-pass response has (a) two critical frequencies (b) one critical frequency (c) a flat curve in the passband (d) a wide bandwidth 4. The lowest frequency passed by a low-pass filter is (a) 1Hz (b) О Hz (c) 10 Hz (d) dependent on the critical frequency 5. The quality factor (Q) of a band-pass filter depends on (a) the critical frequencies (b) only the bandwidth (c) the center frequency and the bandwidth (d) only the center frequency 6. The damping factor of an active filter determines (a) the voltage gain (b) the critical frequency (c) the response characteristic (d) the roll-off rate 7. A maximally flat frequency response is known as (a) Chebyshev (b)…
(b) Analyse and obtain the transfer function for the filter as shown in Figure Q2(b). R2 R1 Vin w Vo Figure Q2 (b)
(b) Analyse and obtain the transfer function for the filter as shown in Figure Q2(b). R2 R1 Vin Vo Figure Q2 (b)
28) In a certain oscillator A = 2O. The feedback circuit must have gain magnitude of: 0.05 0.025 0.035 none of the above 29) 555-MMV with R=10 Khom, C=0.1 microF has T= ?: 1.098 us O 1.098 ms 0.1098 ms 30) opamp-AMV with time constant3D0.1 ms, beta=D0.6 ,its frequency will be : 3.6 KHz 0.36 KHz O 360 KHz
The circuit in Figure 1 represents the circuit model of an interference path from source vin to the 10 MQ load resistance at vout- C1 C2 1 pF 1000 pF R V in out 10 MQ Figure 1. Interference modeling a) Determine the transfer function H(f) = vou/Vin from vin to vout- b) Determine the output magnitude vout when Vin is a 170V pk sine wave at 60HZ c) Determine the output magnitude vou when vin is a 1V pk sine wave at 1 MHz
(b) Analyse and obtain the transfer function for the filter as shown in Figure Q2(b). R₁ VW HH R₂ W Figure Q2 (b)
Consider the design of a low frequency differentiator to achieve the differentiation gain K = 0.001, and the highest frequency of the input signal is fH = 1000HZ. Determine the value of Ri, and Rf based on the criterion fb = 10fH.Assume that capacitor value is C = 0.1uF Ri= Rf= Ohms Kilo Ohms
I designed a summing amplifier that could amplify a 1mV sinusoid (Vina) into a sinusoid with 1V amplitude and 3.5V offset. The value for R1a is 1k ohms, for R1b is 1mega ohms, R2 is 1 mega ohms, and Vin b is -3.5V. What is the input offset voltage?