EXAMPLE 2 A body of 12 mm diameter is tested and the following results are noted. gauge length =200mm, load =20 kN., change in length =0.2mm, change in diameter at proportional limit = 0.0025 mm. Calculate the value of poison's ratio and young's. modulus. Given data; - D=12 mm. L= 200mm. P= 20 kN AD = 0.0025 mm AL= 0.2mm 1-u?? 2- E??

EXAMPLE 2 A body of 12 mm diameter is tested and the following results are noted. gauge length =200mm, load =20 kN., change in length =0.2mm, change in diameter at proportional limit = 0.0025 mm. Calculate the value of poison's ratio and young's. modulus. Given data; - D=12 mm. L= 200mm. P= 20 kN AD = 0.0025 mm AL= 0.2mm 1-u?? 2- E??

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Stress analysis Task Question / Calculate the critical design loads applied to the Stirling Engine when in operation and provide a stress analysis on the piston .use a factor of safety of 5. Assume outside temperature (bottom plate) is -233 degC and an internal PC board (top plate) is 85 degC ? wwbewn Figure 1.1 show measurement to help you to find the volume / Area Ø1.50 Ø8 Ø 10 - Show your calculations and the analysis and find the applied load on it
Given: • Rod A: Length = 40mm Rod B: Length = 60mm Determine: ● ● Area = 3 cm x 3 cm Area = 4 cm x 4 cm Stress in each rod. Deflection of rigid beam at point D D 0.5m B 0.5m 100KN E = 200 GPa E = 200 GPa A + RIGID CEAM
Use analytical method L1 = 3m L2 = 9m L3 = 3m
Only 100% correct answer will be accepted. Rest will be down voted. Be careful A steel pipe of length L=3.5m, outside diameter d₂ = 0.8m and inside diameter d: 0.6m. The inside of the pipe is a neatly fitted copper rod. The unit is compressed by an axial force P=100 kN. The modulus of elasticity E steel = 300 GPa copper = 117GPa. Determine the following quantities for the pipe: 1) The stress on the pipe? 2) The longitudinal Strain and the subsequent change in length?
During a tensile test on a specimen the following results were obtainedload(KN) 15 30 40 50 55 60 65 70 75 80 82 80 70extension(mm) 0.05 0.094 0.127 0.157 1.778 2.79 3.81 5.08 7.62 12.7 16 19.05 22.9diameter of gauge length=19mmdiameter at fracture=16.49mmgauge length=100mmgauge lengthat fracture=121mmplot the complete load extension graph and the straight line portion to an enlarged scale .hence determinethe modulus of elasticitythe percentage elongationthe percentage reduction in areathe nominal stress at fracturethe actual stress at fracturethe tensile strength
From the figure shown which of the following gives the best outside dimension of the square tubing in increments of 2mm. D = 875 kN SECT. 2 Square Tubing L = 1450 kN SECT. 1 Pipe So Fy = = 290 mPa Do 4.8m So So = outide dimension D, = outside diameter t = 12mm t = 12mm O 280 mm 300 mm O 258 mm O 250 mm
Strength of materials - ENGR 3321 The answer should be: 13.8 MN/m2; 5.94 cm from tip of T
TWO CONCRETE BLOCKS WEIGHING 1800 N EACH FORM PART OF THE RETAINING WALL OF A SWIMMING POOL. WILL THE BLOCKS BE IN EQUILIBRIUM WHEN THE POOL IS FILLED, AND THE POOL EXERTS THE LINE LOADING SHOWN? IF YES, WILL IT SLIDE OR TIP? ALSO, DETERMINE THE HEIGHT OF WATER IN WHICH THE POOL WILL BE FILLED SUCH THAT THE BLOCKS WILL BE IN EQILIBRIUM." 300 mm |- 540 mm H=0.5 540 Plastic mm liner Hy = 1.0 6 N/mm
QUIZ 11. In ammunition testing center the pressure is found to be 255 MPa. Calculate the changein volume of the piece of the copper piece when subjected to this pressure inpercentage. The bulk modulus of copper is 1.38 x Pa.2. Two liters of water, when subjected to a pressure of 10 atm, are compressed by 1.013cc. Find the compressibility of the water. Note: Compressibility = 1/K.3. A solid rubber ball has its volume reduced by 14.5% when subjected to uniform stress of1.45 x 10 4 N/m 2 . Find the bulk modulus for rubber.4. The capillary rise when a glass capillary tube of diameter 0.4mm is dipped vertically inolive oil is 3.8mm. If the angle of contact of olive oil with glass is 0 deg and the density ofolive oil is 920 kg/cu.m, find the surface tension of olive oil.5. A liquid rises to a height of 9cm in a glass capillary of radius 0.02 cm. What will be theheight of the liquid column in a similar glass capillary of radius 0.03 cm?
Q1: Shaft subjected to the loadings in phase shown such that: T=0 N.m to 200 N.m M=-200 to 200 N.m The shaft has d1=60 mm, d2=40mm, r=8 mm, cold drawn, operating temp. 550 C, relaibility of the data 99.9%, Material Properties; out = 1260 MPa, Out=813 Mpa. Is the shaft fails for infinity life design? T. M di d
A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the beam if the working stress in bending is 15 MPa. w = 3 kN/m 5kN Cross-section 1kN.m b 1m Upload 250mm Choose a File 1m E 2m
Question 240K-ft where E = 1800 kst I= 13,432 int 24 Ft Cal culate andl draw the deformed Shafe. Show O, o, and A values where O = Curvature, o = angle of rotation, A = %3D displacement