Design a 4-bit counter C( represented by C3C₂C₁C)which can count the specified sequence as following: 0000011010010010 →11000000. The counter will use the falling edge of the clock denoted by Clk) and have a separate reset pin (R) which will reset the counter to 0000 when it is low (e.g. = 0). Please use D type Flip-flops. Write down the state diagram, and state table; Use K-map to simplify the input equations; Write down the simplified input equations and draw a neat circuit diagram. (Hint: use don't care for unused states)

Design a 4-bit counter C( represented by C3C₂C₁C)which can count the specified sequence as following: 0000011010010010 →11000000. The counter will use the falling edge of the clock denoted by Clk) and have a separate reset pin (R) which will reset the counter to 0000 when it is low (e.g. = 0). Please use D type Flip-flops. Write down the state diagram, and state table; Use K-map to simplify the input equations; Write down the simplified input equations and draw a neat circuit diagram. (Hint: use don't care for unused states)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

5. JK flip-flops are often used to build counters. The JK flip-flop will toggle the original output value when triggered by the clock signal if both the J,K inputs are connected with a constant "high"(logic 1). All the JK flip-flops in Figure 2 are negative edge triggered. All the initial values of Q2Q1Q0 are 0. Qo (LSB) (MSB) Input K K Logic 1 Input Q2 000 Figure 2. Counter (a) Sketch the output waveforms forQ2 Q1 Q0. Write down the output binary value (Q2Q1Q0: such as "000", "001") for each clock period on the figure. (b) Describe the function of the counter (e.g. binary down counter counting from 7 to 0).
show the waveforms for each flip-flop output with respect For the ring counter in Figure to the clock. Assume that FF0 is initially SET and that the rest are RESET. Show at least ten clock pulses. D D. FFO FF1 FF2 FF3 FF4 FF5 FF6 FF7 FF8 FP9 CLK
Problem Statement: You design a circuit of a decade counter that will count from 0-9 only. You will only be using the following: (a) Button – only 1 button will be used to trigger the counting. (b) Flip flop IC to used as counting circuit with 4 - BITS binary OUTPUT. (c) IC's for Decoding the Binary OUTPUT of Flip-flops to Decimal Output (d) 7- Segment Display to display the OUTPUT from 0-9. Block Diagram: 4 Bit Binary Flip-Flop 7-Segment Display Button Decoder Circuits Circuits
1.) A storage register made up of six D flip-flops is storing a binary word. The flip-flop status are: A = set, B = set, C = reset, D = set, E = reset, and F = set. The A flip-flop is the LSB. The decimal equivalent of the register content is 2.) D flip-flops are most frequently used in
You want to design a synchronous counter sequential (sequential) logic circuit. It will count from 0 to 9 and will not count the decimal digits in the last two digits of your student number. a. List the process steps that you will apply in the design approach. Create the State Chart and State Chart. b. Design the sequential circuit using JK Flip-Flop. Explain each step. Show that it has performed the desired action. last two numbers 02
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 9 to 0 and will not count the last digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last digit student num:4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
Design 1-5 count-up Counters using JK Flip-Flops. 001-010- 011-100- 101- back to 001 03 Required: a) Excitation of Flip-Flop b) State diagram and circuit excitation table. c) Obtain simplified equations using k-map. d) Design logic diagram.
Design a sequence detector that detects the sequence 1010. This detector has one input X, and one output Y. The output Y is set to 1 only when the input sequence for X is a 0 followed by a 0 by followed by another 0 and finally followed by a 1, detecting the sequence, otherwise the output Y is set to 0. Using D-type flip-flops in designing this detector. 1.Show the state diagram 2.Show the state table3. Draw the logic diagram of the designed device
Which one is true for D flip flop? a) It has 2 inputs 1 output b) It has always the output 1. c) The output of it will be equal to its' input. d) It can not be used in logic circuit designs.
16. The following serial data are applied to the flip-flop through the AND gates as indicated in Figure 7-85 Ⓒ. Determine the resulting serial data that appear on the Qoutput. There is one clock pulse for each bit time. Assume that Q is initially 0 and that and PRE are HIGH. Rightmost bits are applied first. J₁: 1010011; J₂:0111010; J: 1111000; K: 0001110; K 1101100, K: 1010101 CLK K₁ CLR Figure 7-85 C K PRE -Q CLR
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 0 to 9 and will not count the last two digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last two digit student num: 0 4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.