Example/ A flocculation basin is designed to treat water of flowof (1 m³/sec) • The Length of the basin is 30m; widthis 12-25 m, and the depth is 4.5 m ‹ The basin is provided byfour Shafts along the length of the basin, for each shaft.there is a two bladdes with 12 m Length and 6.3m widthThe center of shaft is 2.m from the center of blades.The drag cofficient is 1.8, blade velocity in the basin is 0-75of total speed of revaluation that to be equal to (2.5xPm)use M - 1.312 x/03 Nis/m² and then determine %-1- The Power input in (kw) units2- The detention time of the basin3- The Value of G

Answered: Image /qna-images/answer/39a34a21-3000-4dd4-9482-46813613297b.jpg

Answered: des with 12 m fl. is 2.m from tis 1.8/…

Engineering

Civil Engineering

des with 12 m fl. is 2.m from tis 1.8/ blade revaluation - 3 Nis/m² 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pipe is use to Connect two reservior, length is 1000m, headloss is 4m, flowrate is 0.6m³/s. Compute the diameter of the pipe IF 1. f = 0.02 2. n = 0.014 3. C=120
7 pt Two wells are located at points A and B respectively. Point C is the middle point between A and B. When water is pumped out from Well A only, the drawdown at C is 5 in. If water is pumped out from both wells A and B with same rate, What is the drawdown (ft) at point C? O10 zero O 15 2.5
Since there is a need to supply more water from reservoir A to reservoir B, it is necessary to lay an additional pipe parallel to it. The existing pipe is 0.6m in diameter with a discharge of 0.5m³/sec between the two reservoirs and 6000m long. Assume f = 0.02 %3| for the old pipe and f = 0.25 for the additional pipe. Determine the following: %3D a. If the additional pipe will have a discharge of 0.65m³/sec of the same length and the head difference between the two reservoirs is constant, find the pipe diameter. ANSWER: h= 25m Existing Pipe Q=0.50m³/sec D = 0.697 m в Additional Pipe b. If the additional pipe of 0.6m in diameter is laid out from the original pipe at its midpoint towards reservoir B, find its capacity. Assume f = 0.02. Also solve for the change in the %3D flow or discharge from A to B. ANSWER: Existing Pipe h=25m QA = 0.7232m/s, QB = 0.3923m³/s, %3D AQ = QA – Q = 0.5271m³/s %3D | в `Additional Pipe
A vertical cylinder having a circular base of radus and a height of 12 m is led with water at the rate of 1 m/min. If the depth of water in the cylinder at the vertical position is 3 m, what would be the resulting depth when the cylinder is in the honzontal position? O A. 0 50 O B.0.40 OD.0.30r «< Question 31 of 50
1. Compute the following volumes. a) V?(1) b) VÝ(2) c) v(3) d) V(4) e) V°(10)
What should be the drainage capacity of the collector pipe? K=5 x 10-4 cm/s
ete solution in landscape orientation by placing it in a short coupon bond 1. Find the y- coordinate of the centroid of the culvert shown. 12 y-4-x2/9 3 12 h 6 cm 2. The enclosed area between two concentric ser
A bar screen is used to treat 10 MGD of menicipal wastewater. The vertical bars are 1.27 cm wide and 3.8 cm deep. The minimum allowable spacing for the bars is 2.4cm. The appoach channel carries the water at velocity of 0.381 m/s and is 1.07 m wide and 1.37 m deep. 1- detrmine the number of bar and spacing that should be used. 2- calculate the head loss through screen when it is clean (m). 3- it's estimated that the screen will remove 227 kg (wet basis) of screenings ber milion gallons of water treated. What will be the daily accumulation (kg and m^3) of the screening if the density of screening 100 kg/m^3.
A channel has been designed to convey clear water to a fish hatchery. The design calls for aflow depth of 2.0 ft and a velocity of 2.0 ft/s. The channel is very wide so the side effects canbe neglected and the hydraulic radius taken as equal to the depth. It is to be constructed insand which has a median diameter ds = 0.915 mm (0.003 ft). For a flat bed in this materialthe Darcy-Weisbach friction factor is estimated to be f = 0.0185 and the required channelslope is S = 0.000145. The water temperature is 20°C and the kinematic viscosity υυ is = 1.08x 10-5 ft2/s. The specific gravity of the sand is 2.65. Clear water is admitted to the channeland it is imperative that no material be scoured from the bed since any sand in the hatcherywill result in instantaneous death of all the fish. Using Shields' diagram, determine if theexisting design is adequate to deliver clear water to the hatchery.
Three pipes A,B and C coonected in seies discharges 160 L/s of water. The properties of pipe: for pipe A,L= 1800 m, diameter= 0.90 m f= 0.012; for pipe B, L= 1500 m, diameter= 0.60 m f=0.012 and for pipe C, L= 800 m , diameter = 0/45 m, f= 0.012. Disregarding minor losses, find the diameter of an equivalent single pipe which can replace the three pipe. answers: a.0.492 m. b.0.750 m. c.1.15 m. d.0.574 m.
Three pipes A,B and C coonected in seies discharges 160 L/s of water. The properties of pipe: for pipe A,L= 1800 m, diameter= 0.90 m f= 0.012; for pipe B, L= 1500 m, diameter= 0.60 m f=0.012 and for pipe C, L= 800 m , diameter = 0/45 m, f= 0.012. Disregarding minor losses, find the total headloss of the pipe. a. 0.492 m. b. 0.078 m. c. 1.15 m. d. 1.675 m.
Two pipes with C1 = 120, connected in series, discharge 4.75 cfs with a loss of head of 27 ft. Each pipe has a length of 1000 ft. If one pipe has a diameter of 18 inches, determine the diameter of the other pipe. Neglect minor losses.