CAT-6 twisted pair cable is a commonly used computer networks cable that provides a frequency bandwidth of up to 250 MHz. It is suitable for most varieties of Ethernet over twisted pair up to 1000 BASE-T (Gigabit Ethernet). Determine whether a signal-to-noise ratio (SNR) of 20 dB is adequate to transmit 0.9 Gbps on this cable?

CAT-6 twisted pair cable is a commonly used computer networks cable that provides a frequency bandwidth of up to 250 MHz. It is suitable for most varieties of Ethernet over twisted pair up to 1000 BASE-T (Gigabit Ethernet). Determine whether a signal-to-noise ratio (SNR) of 20 dB is adequate to transmit 0.9 Gbps on this cable?

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 27VE

See similar textbooks

Similar questions

Efficiency Principle:Ethernet V1 access protocol was designed to run at 10 Mbps over 2.5 Km using 1500 Byte packets. This same protocol needs to be used at 100 Mbps at the same efficiency (utilization). What distance can it cover if the frame size is not changed? (Note: be careful with the units.
Shielded twisted-pair (STP) cabling was first made popular by IBM when it introduced Type classification for data cabling. Though to purchase and install than UTP, STP offers some distinct advantages. Shielded twisted-pair (STP) cable can up to 600MHZ. STP has an more currently support applications requiring shield that consists of braided . The shield surrounds the 150-ohm, 22 AWG, two-pair conductors. Each is insulated with a to install than UTP. STP cabling solely material and then each twisted pair is individually shielded. STP cabling is because it provides better EMI protection and potential bandwidth, installers consider using fiber-optic cable instead. conductor copper material bandwidth expensive dielectric inner glass Cheap lower Interference expensive WAN higher outer
Coaxial cable has been around since local area networking was in its invented. The original designers of Ethernet picked coaxial cable as their "ether" because the coaxial cable is well it has high bandwidth capabilities and low and is easy to install. Coaxial cables are identified by their RG standard. Coaxial cable can have a or stranded core and impedance of 50, 75, or 92 ohms. The Coaxial has wire that carries the signal surrounded by a layer of and another concentric ; both the shield and the inner conductor run along the same axis. The shield also serves as a ground and should be grounded to be effective. Coaxial cable is still widely used for video applications; in fact, its use is increasing due to the greater demand for However, it is not recommended for data installations and is not recognized by the Standard for such. Noise outer two local area networks CCTV wire solid cladding expensive inner insulation one shielded attenuation Telephone shield
Given a transmission rate of 1 Gbps and a propagation speed of 200m / μ sec , how many meters of cable are needed for a full duplex transmission link to have a minimum capacity of 1500 bytes?
Calculate the spectral efficiency for an old 56K internet connection modem that can transfer 56,000 bit/s downstream and 48,000 bit/s upstream over an analog telephone network and the frequency range is limited to between 300 hertz and 3,400 hertz?
Consider a CSMA/CD network that transmits data at a rate of 100 Mbps (108 bits per second) over a 1 km (kilometer) cable with no repeaters. If the minimum frame size required for this network is 1250 bytes, what is the signal speed (km/sec) in the cable?
In a CSMA/CD network with a data rate of 10 Mbps, the minimum frame size is found to be 512 bits over maximum cable length 2500 m. what should be the maximum cable length if we increase the data rate to 100 Mbps?
Q) In pure ALOHA protocol the highest throughput is achived when G= and the channel can have a maximum utilization value of about percent.
In ADSL, the OFDM symbol rate across all subcarriers is 4000 symbols per second. Assume that in the downstream direction, 25 subcarriers use 1024-QAM, 50 use 256-QAM, 100 use 64-QAM and 100 use 16-QAM. What is the overall bit rate
. For a 10 Mbps Ethernet with 100 stations connected to it has 50 % efficiency. Velocity of propagation is 2.1 x 10 m/sec. Find the ratio of transmission to propagation delay.
Find correct answers referes to data and networking communication: 1. In ethernet frame, sending adapter encapsulates IP datagram (or other network layer protocol packet) and it uses preamble whick consists of :a. 4 bytes with pattern 10101010 followed by one byte with pattern 10101011.b. 7 bytes with pattern 1010111 followed by one byte with pattern 10101011.c. 2 bytes with pattern 10101010 followed by one byte with pattern 10101011.d. 7 bytes with pattern 10101011 followed by one byte wit pattern 10101010.e. 6 bytes with pattern 10101010 followed by one byte with pattern 10101011.f. 7 bytes with pattern 10101011 followed one byte with pattern 10101010.g. 7 bytes with pattern 10101010 followed by one byte with pattern 10101011. 2. The method of communication in which transaction takes place in both directions but only in one direction at a time is called?a. three answers are correctb. two answers are correctc. Multi-duplexd. Full-duplexe. four wire circuitf. simplexg. half-duplexh.…
A 1 Mbps link is used to transfer packets of each 10,000 bits long. This includes 500 bits header. If the channel is error free and 270 msec is the signal propagation time from the source to destination, obtain the efficiency for, (1) Stop and wait protocol. (i) Sliding window protocol with window size of 500. (iii) Sliding window protocol with window size of 10.