Thanks ayo.EQUIVALENT SCHEMATICHA741, µA741C, SA741C08Q12013INVERT.R7a15INPUTNON-INVERTINGINPUT0 24.5kS!Rg32512Q18R5R8O OUTPUT39k!!7.5k!!R105012K16K 020010OFFSETNULL022OFFSET NULL O1R1R2R3R4R12R1150k!!50!?1ks?50k!!1k!!5ks! Assume V+ =12 volts and V-= -12 volts. VBE(on)= 0.7 volts. RL = 2 k2 connected to the OUTPUT terminal. Answerthe following questions:(a) The configration of Q11, Q1o, Q12, and Q13 is a (Class A, Class B, Class C, ClassAB) amplifier(b) If v.(t) = 10 cos(ot) volts, compute the peak and average power in RL = 2kN.(c) If v.(t) = 10 cos(ot) volts, compute the collector efficiency, nc=.compute the collector efficiency, nc=_% and if vo(t) = 12 cos(@t) volts,(d) If vo(t) is a 24 volt, peak -to-peak square wave, the power dissipation in Q14 and Q20 approaches(72 mW, 36 mW, 0 mW, t/4x(12/24) mW) Circle your choice.(e) The voltage gain of the Q14-Q20 circuit is about (200,000, -1.0, +1.0, Computed from -g„R1) Circle choice.(f) The Q15 circuit operates to limit the Q14 collector current to what value?

Given: In this question, the given details are, Assume V+ =12 volts and V-= -12 volts. VBE(on)=0.7…

Assume V+ =12 volts and V-=-12 volts. VBE(on)= 0.7 volts. R₁ = 2 kn connected to the OUTPUT terminal. Answer the following questions: (a) The configration of Q11, Q10, Q12, and Q13 is a (Class A, Class B, Class C, ClassAB) amplifier (b) If v.(t) = 10 cos(@t) volts, compute the peak and average power in R₁ = 2kQ. (c) If v.(t) = 10 cos(ot) volts, compute the collector efficiency, nc= compute the collector efficiency, nc=_ % % and if v.(t) = 12 cos(@t) volts, (d) If v.(t) is a 24 volt, peak-to-peak square wave, the power dissipation in Q14 and Q20 approaches (72 mW, 36 mW, 0 mW, л/4x(12/24) mW) Circle your choice. (e) The voltage gain of the Q14-Q20 circuit is about (200,000, -1.0, +1.0, Computed from-g_R₁) Circle choice. (f) The Q15 circuit operates to limit the Q14 collector current to what value?

Assume V+ =12 volts and V-=-12 volts. VBE(on)= 0.7 volts. R₁ = 2 kn connected to the OUTPUT terminal. Answer the following questions: (a) The configration of Q11, Q10, Q12, and Q13 is a (Class A, Class B, Class C, ClassAB) amplifier (b) If v.(t) = 10 cos(@t) volts, compute the peak and average power in R₁ = 2kQ. (c) If v.(t) = 10 cos(ot) volts, compute the collector efficiency, nc= compute the collector efficiency, nc=_ % % and if v.(t) = 12 cos(@t) volts, (d) If v.(t) is a 24 volt, peak-to-peak square wave, the power dissipation in Q14 and Q20 approaches (72 mW, 36 mW, 0 mW, л/4x(12/24) mW) Circle your choice. (e) The voltage gain of the Q14-Q20 circuit is about (200,000, -1.0, +1.0, Computed from-g_R₁) Circle choice. (f) The Q15 circuit operates to limit the Q14 collector current to what value?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(b) For a digital-analog converter, sketch a five-stage ladder network using 10 k2 and 20 kQ. (c) What is the % resolution of the ladder network found in part (b)? (d) With a reference voltage of 32V for the ladder network found in part (b), calculate the output voltage for an input of 11101.
4. A current measuring operational amplifier is made by bridging a resistor across the inverting terminal (pin 2) and the output terminal (pin 6). The noninverting terminal is grounded. a. Draw a sketch of the current measuring circuit. Determine an appropriate resistor for converting a current of 1.0 picoamperes (1.0 × 10-¹2 A) to a voltage of 0.010 V. (The math for this question is very easy, don't overthink this question. b. There are a few reasons that circuit you drew in part a will not be effective. First, you will have a difficult time finding a resistance with the required resistance value. Second, the input terminals do not have infinite resistance value. In fact, for an inexpensive 741 op-amp, the input terminal resistance may only be a few MOhms, which is far less than the resistance your calculated for the feedback resistor. This means that more current will be drawn into the op-amp than will go around it. Finally, the op-amp may have a bias current that is larger than the…
For the 2 circuits shown above, βnpn = 100, βpnp = 50, VDO = 0.7 V, R2 = 150 kΩ, and RB = 12 kΩ Using the ac small-scale signal analysis, determine for each circuit: a) The voltage gain (Av = vout/vin) b) The input resistance (Rin) c) The output resistance (Rout)
1- a) Draw the circuit of a V-I converter and derive an expression for the output current in terms of input voltage. b) Draw the neat diagram of analog multiplier using log-antilog amplifiers and explain its operation
A single stage amplifier has a voltage gain of 60. The collector load RC = 50092 and the input impedance is 1k02. Calculate the overall gain when two such stages are cascaded through R-C coupling.
In the voltage regulator circuit shown in the figure, the op-amp is ideal. The BJT has VBE=0.7 V and Beta = 100, and the Zener voltage is 4.7 V. For a regulated output of 9 V, the value of R (in Ohms) is Express answers in two decimal points. Show solution on your answer sheet. V = 12 V Vo = 12 V 1 k2 1 k2 AV2 = 47 V %3D ww
C. A variable capacitor. O d. An amplifier. When operating in the saturation region, the current gain 'B' of the bipolar transistor increases Select one: OTrue O False Assume Is= 8x 105 A, B-100, and VA =-. For the circuit shown below and for -0.5 mA, the value of the transconduce Vcc=2 V Q1
Design a circuit to simulate the following mathematical equation using minimum number of operational amplifiers. 5f Vout = 12V1 +5 V2 dt + 6 Where Vout is the output voltage, V1 and V2 are the input voltages. Assume that the available Dc source is +/- 5 volt.
Q/ Use The following circuit to design an oscillator of 5KHZ out The amplifier used in this oscillators is multistage C.S with Source resistance amplifier. The design must be with minimum No. of stages. use The following FET Parameter Id=2MA, gm= 2.5ms and rds= 40K ohm use VDD=24volt. R
Prob 1: For each of the 8 circuits below, draw small signal model and calculate Vout/Vin. Vb1, Vb2 are dc voltage sources. and I1 is an ideal dc current source. Ignore body effect for all problems. Vino M3 M₂ M₁ (a) VDD J Vb₁ M3 (e) VDD VinM₂ Vb2M₁ Vb3 Vb2 - Vout Vb1 Vout HE Vout o Vb₁ VinM₂ 46! M3 (b) VDD B M₁ T. M3H (f) VDD VinM₁ M₂ Vout VinM₂ 4M₁ (c) M3 M3 VDD VDD 74 Vb1M₂ Vino M₁ (g) Vout Vout Vb1 Vb2 HE Vin VinM₂ M3 M3 VDD (d) HL M₁ M₁ -o Vout M2o Vout 1₁ (h) VDD
The circuit shown in the following in figure has: VIN= 10 V, Vz = 7.2 V@ Iz-40 mA, Izk =2 mA, IzM= 100 mA and Zz-5 2. Determine a) Maximum output voltage. b) Minimum output voltage. c) The percentage load regulation. d) The minimum permissible load resistor value. c) The maximum permissible load resistor value. R 2211 VIS
In series compensation, if the series applied voltage is in quadrature with the liner current: A. The series compensation cannot supply or absorb reactive power B. The series compensation can only supply active power C. The series compensation can only absorb active power D. The series compensation cannot supply or absorb active power