An industrial process involves the measurement of the flow rate of water in a pipeline using an orifice plate of area Ao, which is related by the following equation. CaAo |2ΔΡ Q 2 i) Sketch its construction ii) Calculate the pressure difference (AP) across the flow sensor, given the following parameters: - Volumetric flow rate, Q = 0.025 m³/s Discharge coefficient, C₁ = 0.6 Density of water, p = 1000 kg/m³ Internal diameter of pipe, Dp = 100 mm Diameter of orifice, D, 50 mm =

An industrial process involves the measurement of the flow rate of water in a pipeline using an orifice plate of area Ao, which is related by the following equation. CaAo |2ΔΡ Q 2 i) Sketch its construction ii) Calculate the pressure difference (AP) across the flow sensor, given the following parameters: - Volumetric flow rate, Q = 0.025 m³/s Discharge coefficient, C₁ = 0.6 Density of water, p = 1000 kg/m³ Internal diameter of pipe, Dp = 100 mm Diameter of orifice, D, 50 mm =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) A pitot-static probe is use to determine the flow velocity by measuring the differential pressure. The pitot formula to obtain the flow velocity is, 2(P- P,) V = where, V is the velocity, P is pressure and pis fluid density. i) The pressure difference sensor use in the system is electronic types and the output of the device is measured in voltage. The output of the pressure device is 3.5 V and the linear relationship between the device and the pressure difference is 10 kPa/V. If the measured fluid is water at 20°C, determine the pressure difference inside the system the water velocity. ii) The Pitot-static tube is also commonly use in aircraft. An aircraft flying at 3000 m above sea level when the differential pressure reading clocked 3 kPa. Determine the speed of the aircraft.
49. Water flows at a rate of 200 GPM into a piping system connected in series. Length, diameter, and loss coefficient of each pipe are given below. For p= 62.4 Ibm/ft and u = 0.7E–3 lbm ft/s find total pressure drop and the diameter of an equivalent pipe representing this system. C) Fluid Power Theory an.. IndPitEn IlIb. Fluid Mechanics: Incompressible Viscous Flow 392 Pipe D K No. (ft) 100.00 (in) 5.00 (-) 50.00 1 2 80.00 4.50 45.00 3 70.00 4.00 65.00 4 120.00 3.50 55.00 5 90.00 3.00 15.00
PLBASE BOX YOUR ANSWERS 3.7 atm -: The 6 cm diameter pipe contains a liquid (p = 1260 kg/m', u = 149 kg/m.s) flowing at an unknown flowrate. Pipe length (A to B) is 40 m. For the gage-pressure measurement shown, find a) the direction of flow (1.e, AB or B→A); b) Is the flow laminar/ turbulent; and c) friction factor. Ignore minor losses. 2.1 atm 12 m
04: For the piping system, compute pressure at A, and mid pipe 2. If pipe (3) & pipe (4) havi equal discharge, and pipe (1) have the same properties of pipe (5). Neglect minor losses. (S F S) Pipe 1 L (m) Pipe 2 460 Pipe 3 300 Pipe 4 365 D (cm) Q (1/sec) 245 30 30 20 38 566 f PB (kPa) Pipe 1 0.027 500 Pipe 2 Pipe 3 rig 4. B Pipe 4 Pipe S
In a 250 mm diameter pipe, oil discharges through a sharp crested round orifice, 100 mm in diameter. If the coefficient of contraction (Cc) and coefficient of velocity (Cv) are 0.63 and 0.98, respectively. SG of oil is 0.86. Determine the following: a) discharge from the orifice, (L/s) given that: coefficient of orifice, Co= Cc x Cv b) diameter of jet (mm) given that: Cc = Ajet/Atheo c) actual velocity in the jet, (ft/s) Note: Maintain 3 decimal places on partial and final answers.
Flow (m³ /h) 1 1.5 2 2.5 Pressure difference Ap (bar) 0.005 0.012 0.021 0.034 Kinematic viscosity 10-6 m?/s V (Rough Pipe Radius = 25mm) (Rough Pipe length =L=80cm) Question: An experiment is made using different flow rates in a pipe and pressure differences are given according to the given flow values. According to these; 1. Calculate the pipe roughness height ( e ). 2. Calculate the Reynolds value. 3. Calculate the coefficient of friction f from the Darcy-Weisbach equation. 4. Briefly describe the equations you use and the reasons for using them.
I6 a) Determine the radial positions of a pitot tube for a 6-point traverse in a 0.3 m inner diameter pipe. Show your calculations. b) If the fluid velocity measured at the pipe center is 0.3 m/s and yields a Reynolds number based on local velocity of 4000, what is the fluid cross-sectional average velocity in the pipe? c) At what value of Re is the discharge coefficient of an orifice meter approximately independent of geometry and flow rate?
The laminar flow of a fluid with a constant viscosity, 4, inside a channel is governed by the following boundary value problem (strong form): d'u dp for y E (0, h) "dy dr u = 0 at y = 0 and y = h vhere u is the fluid velocity and is the pressure drop in the direction of the flow. a) Derive the weak form of the boundary value problem described above.
For the following questions, Circle the correct answer Q1. We have a steady fully rough turbulent flow of water with constant density in a cylindrical pipe of constant diameter. The height of the uniform roughness elements in the pipe is k.. . . For a fully developed rough turbulent flow in the pipe, the condition ku. -> 70 is the same as k,> 66,. [True/False] V avg The wall shear stress T-pfU/8. It is applicable only for steady fully rough turbulent flow in the pipe. [True/False] The shear stress distribution is linear with the radial distance from the pipe centerline only for laminar flow. [True/False] The head loss per unit length is quadrupled when the discharge is doubled. [True/False] The piezometric pressure drops uniformly along the pipe because the flow is steady along the pipe [True/False]
2:35 A U * N a 95%i This document contains ink, shapes and im.. Data Sheet: F9a: Fluid Mechanics & Bernoulli's Principle NAME: DATE: width port 1 & 3 6.3960E-03 (m) width port 2 & 4 2.8750E-02 (m) depth all ports 7.0060E-03 (m) air density 1.1929 (kg/m³) Cross sectional area Data Sheet: F9a: Fluid Mechanics & Bernoulli's Principle NAME: DATE: Density of Air: 1.2129 kg/m3 Table 1: Measured Data for Apparatus 6.3960E-03 m Chamber Width Port 1 & 3 2.8750E-02 m Chamber Width Port 2 & 4 7.0060E-03 m Chamber Depth at all Ports Width Depth
Suppose we have planned to design a hydraulic system.In this aspect, the pump selection is to be finalized for a flow rate of 3299.5 Liters per minute, It has been validated that the fluid velocity in a discharge pipeline should be between 3.6 m/s and 6.92 m/s. Calculate the minimum diameter and maximum diameter of pipe that should be used in the pipelines Area of the maximum sized pipe diameter (in m2) Area of the minimum sized pipe diameter (in m2) The minimum sized pipe diameter (in cm) and The maximum sized pipe diameter (in cm)
Q// Upon completion of the Reynolds experiment, we had this information. The tube diameter was 0.03 m, time is 14 sec and the lamellar bisection type 'Find Q flow rate m^3/s , Re, viscosity and velocity m / s at a temperature of 26 ° C for water.