An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.33, what will be the lateral strain? 30. E = 6/8 v = -e(lateral) e(axial)

An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.33, what will be the lateral strain? 30. E = 6/8 v = -e(lateral) e(axial)

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Related questions

Q: A solid circular bar is acted upon by tensile force of 20N. The diameter of circular Bar is 10 mm.…

A: Given Tensile force, F = 20 N Diameter of bar, d = 10 mm Change in Length of bar, L' = 0.2 m…

Q: A 3000 kgf tensile load is applied on a steel bar of 3.25 cm diameter. When the same load is applied…

A: Given data: P=3000 kgfDsteel=3.25 cmEsteel=2.1×106 kgf/cm2Eal=0.7×106 kgf/cm2

Q: ven the stress-strain data from a tension test, how do you find the following : a) The modulus of…

A: Solution on below attachments

Q: A round bar have a radius 8 cm and subjected to an axial tensile force of 10 kN. Determine the axial…

A: Given data : Youngs Modulus (E)=70 GPaRigidty Modulus (G)=26 GPaPoisson's ratio=μRadius (r)=8…

Q: A plate in equilibrium is subjected to uniform stresses along its edges with magnitude o = 30 MPa…

Q: Question 3 o(MPa) The elastic portion of the stress-strain diagram for a steel alloy is shown in the…

A: GIVEN DATA:- ORIGINAL DIAMETER=15MM ORIGINAL LENGTH=60MM INITIAL APPLIED LOAD=20KN FINAL DIAMETER…

Q: The specimen shown is made from a 25 mm diameter cylindrical steel rod with two 38 mm outer-diameter…

Q: A plate 2 m x 2 m x 20 mm is subjected to stress o, 100 MPa (tensile) and o, = 50 MPa (compressive)…

Q: The poisson ratio of an elastic material is 0.3, then the ratio of its young's modulus and bulk…

Q: Diameter of the metal bar, before and after load application was measured to be 100.00 mm and 99.99…

Q: 2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as…

A: Given data Area of steel=300mm2=300×10-6 m2 Area of aluminium=300mm2=300×10-6 m2 Area of…

Q: 60,000 40,000 20,000 0.002 0.004 0.006 0.008 Strain, in./in. Stress, psi

A: The given stress-strain graph of aluminum alloy is-

Q: A 10.0 mm diameter cylindrical specimen of a bearing bronze material is pulled under uniaxial…

A: given-10.0 mm diameter 1500 N force∆d=0.67 mmn=0.35

Q: An elastic bar of length L, uniform cross-sectional area A, coefficient of thermal expansion a , and…

A: Solution; The axial stress diagram; σ varies with ∆T and does not depends upon the length of bar.

Q: Problem 1 A bar obtained by bonding together pieces of aluminum (E, = 70 GPa) and brass (E, = 105…

A: We have to determine the value of largest moment M that can be applied about the horizontal axis…

Q: An aluminum alloy rod has a circular cross section with a diameter of 8 mm. This rod is subjected to…

A: It is required to calculate the stress in the circular rod. Here, A0 is the original area of the…

Q: In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is…

Q: A steel bar is stressed to 280 MPa. The modulus of elasticity is 205 GPa. The bar is 80 mm diameter…

A: Given data:- Stress in steel barσ = 280 mpa = 280 N/mm2 Modulus of…

Q: 3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure.…

A: The free body diagram of the rod is given:

Q: An applied torque results in a shear strain (y) of 3.75 x 10-3 in a solid circular steel shaft. At…

Q: calculate the lateral strain and the change in diameter.

Q: A fabric used in air-inflated structures is subjected to a biaxial loading that results in normal…

Q: An aluminium rod is rigidly attached between a steel rod and a bronze rod as shown in Figure 3.…

A: It is required to find the maximum value P that can be applied and then total Elongation of rods.

Q: The cross-section of a composite beam made of aluminium and steel is shown in the figure. The moduli…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure…

A: Given cross-sectional area of Steel = 522 mm2; Aluminum = 439 mm2; Bronze = 211 mm2 Length of Steel…

Q: The polymer bar shown in the figure below has a width of b=40 mm, a depth of d=104 mm, and a height…

A: we knowσ=FA=-125100040×104=-30.048mpaεax=δhh=-2.4255

Q: Problem 13.1. The aluminum machine part is subjected to a moment of M = 75 N.m. Determine the…

A: M=75 N-marea of the flangeA1=10×40A1=400 mm2distance of centroid of the flange from…

Q: 3. The distribution of stress in an aluminum machine component is given (in megapascals) by Ox = y +…

A: The stress tensor is:

Q: Shear modulus (G) is the ratio of O a. Linear stress to lateral strain O b. Volumetric strain to…

A: Option C is correct. Shear stress to shear strain

Q: An aluminum alloy rod has a circular cross section with a diameter of 7mm. The rod s subjected to a…

Q: 1: For a material stress at proportionality limit is 400 MPa and modulus of elasticity is 200 MPa.…

Q: A 5-mm-thick rectangular alloy bar is subjected to ajtensile load P by pins at A and B, as shown in…

A: P=24kN

Q: 600 480 600 480 360 360 240 240 120 120 0.000 0.006 0.002 0.004 Strain 00 0.04 0.08 0.12 0.16 0.20…

Q: A bar of length 2.0m is made of a structural steel having the stress-strain diagram shown in the…

Q: (a) Determine the elastic strain when a stress of 80 MPa is applied to the model (rheological )…

A: We have to determine the value of elastic strain when stress of 80 Mpa is applied to the model…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: Modulus of rigidity may be defined as the ratio of O(A) Linear stress to lateral strain O(B) Lateral…

A: Modulus of rigidity is also known as shear modulus . It is defined as the ratio of shear stress upon…

Q: Stress and Strain A metal wire 2.5mm in diameter a 2m long. A force of 12N is applied to it and it…

A: To find Stress,strain and modulus of elasticity??

Q: a Steel bar Stress (fs) in terms of steel Modulus of Elasticity (Es), steel tensile strain (et),…

A: Following are required answers :

Q: 1. For each state of plane stress shown below, i.e., for configurations (a) and (b), indicate…

Q: Ox =10 MPa (compressive) Figure below shows the state of stress at a critical point on a component…

A: Stress is the internal resistance force that develops in the body due to the applied force that…

Q: A circular aluminum tube of length L=500 mm is loaded in compression by forces P (see figure (a)).…

Q: Q.1 The yield stresses (oy) have been measured using steel and aluminum specimens of various grain…

A: Given data:

Q: Aluminum A = 400 mm? Bronze A = 200 mm? Steel A = 500 mm? 2P 4P 2.5 m 2.0 m 1.5 m P.

Q: A steel rod is subjected to a gradually applied load (F) which gave a rise to a maximum stress of…

A: Given that, Maximum stress =200 Mpa Length = 250 mm, Circular with diameter = 25 mm, Total starin…

Q: 2. A steel bar of 750 mm2 cross-sectional area is placed between two aluminum bars, each of 500 mm2…

A: Area of steel = 750mm2 Area of aluminum = 500mm2 Es = 210GPa Eal = 70GPa (σy)s = 240MPa…

Q: 3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure.…

Q: Material specimens always break at ultimate stress. In the plastic region there is permanent…

A: False True False False False

Q: A 3m long steel plate having a cross section of 25mm by 300mm is use as a hanger and subjected to a…

A: Schematic diagram of the given problem:

Q: 2. Given a 5 mm diameter steel wire, which is 4 meters long, carries an axial tensile load P. Find…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

30.
An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod
is subjected to a tensile load of 5kN. Assume that the material is in the elastic region
and E = 69 GPa. If Poisson's Ratio is 0.33, what will be the lateral strain?
E= 6/8
v = -E(lateral)/(axial)

Expert Solution

Step 1<

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E=69 GPa If Poisson's Ratio is 0.33, what will be the lateral strain? E=68 v=-e(lateral) e(axial)
An aluminum alloy [E = 67 GPa; ν = 0.33; α = 23.0 × 10–6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 225 mm, a cross-sectional area of A = 5100 mm2, and a length of L = 4.1 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by ΔT = 63°C, the longitudinal normal strain in the plate is found to be 2900 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Δd.
An element in plane stress is subjected to stresses o, = -8400 psi, ay = 1100 psi, and ty = 1700 psi (see figure). The material is aluminum with %3D modulus of elasticity E =10,000 ksi and Poisson's ratio v = 0.33. Determine the following quantities: (a) the strains for an element oriented at an angle 30 degrees, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements. Ty Txy Ox
An aluminum alloy [E = 69 GPa; v = 0.33; a = 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 215 mm, a cross-sectional area of A = 5100 mm2, and a length of L = 3.9 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 53°C, the longitudinal normal strain in the plate is found to be 2320 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L Answer: (a) P = i (b) Δd = = i d KN mm
X Your answer is incorrect. An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm. The cross-sectional dimensions of the beam are b1 = 39 mm, d1 = 82 mm, b2 = 23 mm, dɔ = 23 mm, and a = 8 mm. For this material, the allowable tensile bending stress is 20 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a d2 y A B b1 Answer: M = 412.360 N•m Attempts: 2 of 3 used
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 840 mm. The cross-sectional dimensions of the beam are b1 = 30 mm, d1 = 108 mm, b2 = 18 mm, d2 = 18 mm, and a = 6 mm. For this material, the allowable tensile bending stress is 17 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a M. d2 d1 | A В
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 800 mm. The cross-sectional dimensions of the beam are b1 = 35 mm, d1 = 108 mm, b2 = 21 mm, d2 = 21 mm, and a = 7 mm. For this material, the allowable tensile bending stress is 20 MPa, and the allowable compressive bending stress is 9 MPa. Determine the largest moment M that can be applied as shown to the beam.
An aluminum alloy [E = 74 GPa; v = 0.33; a = 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 265 mm, a cross-sectional area of A = 5300 mm², and a length of L= 4.2 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 57°C, the longitudinal normal strain in the plate is found to be 2920 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L P Answer: (a) P = i (b) Δd = i kN mm
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm. The cross-sectional dimensions of the beam are b1 = 33 mm, d1 = 93 mm, b2 = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 16 MPa, and the allowable compressive bending stress is 9 MPa. Determine the %3D largest moment M that can be applied as shown to the beam. b2 M d2 d1 | A B L b1 Answer: M = i N•m
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm. The cross-sectional dimensions of the beam are b, = 36 mm, d1 = 95 mm, b2 = 22 mm, d2 = 22 mm, and a = 7 mm. For this material, the allowable tensile bending stress is 11 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 M d2 d1 |A В b1 Answer: M = N-m
A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a tensile axial force P, its diameter is decreased by 0.018 mm. Assume the Poisson’s ratio to be 0.33. Determine the value of loads P and its axial deformation. P = ? N δ = ? mm
X Your answer is incorrect. An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 760 mm. The cross-sectional dimensions of the beam are bị = 33 mm, di = 102 mm, bz = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 10 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 d2 A В b1 Answer: M = 457.082 N-m Save for Later Attempts: 2 of 3 used Submit Answer Usine mutinle attemnts has imnacted vour score