A three-phase 6-pole 400-volt cylindrical-rotor synchronous machine has negligible armatureresistance and armature reactance of j1.2 ohms. The machine is operated as a motor suppliedby a 60-Hz supply at rated voltage. What will be the operating speed of this motor? Express youranswer in RPM.a.3600 RPMb. None of these are correct.C.1200 RPMO d. 2400 RPMe.3000 RPM

In this question we will find operating speed of synchronous motor.....

A three-phase 6-pole 400-volt cylindrical-rotor synchronous machine has negligible arr resistance and armature reactance of j1.2 ohms. The machine is operated as a motor by a 60-Hz supply at rated voltage. What will be the operating speed of this motor? Exp answer in RPM. O a. 3600 RPM b. None of these are correct. O C. 1200 RPM O d. 2400 RPM 3000 RPM

A three-phase 6-pole 400-volt cylindrical-rotor synchronous machine has negligible arr resistance and armature reactance of j1.2 ohms. The machine is operated as a motor by a 60-Hz supply at rated voltage. What will be the operating speed of this motor? Exp answer in RPM. O a. 3600 RPM b. None of these are correct. O C. 1200 RPM O d. 2400 RPM 3000 RPM

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q-4 100 MVA, 50 Hz alternator is operating at rated speed. The H constant of the machine is 5 MJMVA. The load suddenly increases by 50 MW. Due to delay in governor action, there is a delay of 0.5 sec in opening of steam value. The frequency deviation in percentage is
3.An induction motor has a rotor resistance and reactance at standstill of 0.1 ohm and 3.5 ohm respectively. At standstill the voltage induced to the rotor is 60volts per phase. If the slip is 5%, determine the rotor current
A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit Part B Value I = HA Request Answer Submit If the dc-to-ac converter has a power efficiency of 90 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. HÅ Value Units Request Answer ? Units ?
ANSWER ALL THE QUESTIONS: A.) Calculate the voltage induced in the armature winding of a 4 pole, wave-wound, dc machine having 728 active conductors and running at 1800rpm. The flux per pole is 30mWb. 1310.4V 468.2 V 720.4 V 236.4 V B.) The direction of rotation of a DC motor is reversed by reversing armature connections adding resistance to the field circuit interchanging the armature and field connection reversing supply connection
Describe the similarities in the construction of a DC motor and a DC generator. Please answer in short point wise and dont copy from other sources i will like lt
Q 5. A wave-wound armature of a 6-pole generator has 51 slots. Each slot contains 20 conductors. The voltage required to be generated is 250 V. What would be the speed of coupled prime mover if flux per pole is 0.07 Wb. If the armature is rewound as lap-wound machine and run by same prime mover, what will be the generated voltage? (Ans. 70 rpm; 83.3 V)
A 120 V shunt generator running at 850 rpm has its armature and shunt field resistance of 0.15 ohm and 50 ohm respectively. It supplies 200 lamps each rated at 60 W, 100 V. The friction and windage and core loss of the machine is 400 W. its armature copper * loss on full load and shunt field loss is 2156.7 W, 240 W 2232.6 W, 240 W O 2232.6 W, 200 W 2156.7 W, 200 W O
• Q5/ in a DC motor. List and describe the types of losses that occur
A DC shunt generator delivers 45 A at a terminal voltage of 220 V. The armature and the shunt field resistances are 0.01 2 and 44N respectively. The stray losses are 375 W. What is percentage efficiency of the DC generator
T-a. The direction of rotation of a single-phase split-phase motor can be change by........ a) reversing the connection of the start winding b) reversing the connection of the run winding c) reversing the connection of the start and run winding at the same time d) "a" or "b", not "c" T-b. Single-phase split-phase motors using an electrolytic capacitor in the start winding circuit should not be cycled more than about__________ time per hour. a) 8 b) 12 c) 24 d) none of the above T-c. When replacing the capacitor in a capacitor-start induction-run motor, one must be sure to replace the bad capacitor with__________ . a) a smaller one b) one of the same size c) a larger one d) none of the above
Q5. A wave-wound armature of a 6-pole generator has 51 slots. Each slot contains 20 conductors. The voltage required to he generated is 250 v. What would be the speed of coupled prime mover if flux per pole is 0.07 Wb. If the armature is rewound as lap-wound machine and run by same prime mover, what will be the generated voltage? (Ans. 70 rpm; 83.3 V) Q6. A 4-pole wave-wound armature rotating at 400 rpm is required to generate 300 V. The effective flux per pole is about 0.05 Wb. If the armature has 120 slots, determine the suitable number of conductors per slot and hence determine the actual value of flux required to generate the same voltage. (Ans. 4: 46.875 mWb)
A three-phase squirrel cage induction machine with rated frequency of f = 50 Hz has a rated slip sn = 0.06. What is the rated speed of the machine in rpm (revolution per minute) if the number of pole-pairs is p = 2? Answer: