A sample of clay having a mass of 675 gm was coated with paraffin wax. The combined mass of the clay and the wax was found to be 682 gm. The volume was found by immersion in water as 345 ml. The sample was then broken to open. The water content and specific gravity of solids were found to be 15 % and 2.70 respectively. Calculate the bulk density of soil, its void ratio, and degree of saturation. Take specific gravity of wax as 0.89.

A sample of clay having a mass of 675 gm was coated with paraffin wax. The combined mass of the clay and the wax was found to be 682 gm. The volume was found by immersion in water as 345 ml. The sample was then broken to open. The water content and specific gravity of solids were found to be 15 % and 2.70 respectively. Calculate the bulk density of soil, its void ratio, and degree of saturation. Take specific gravity of wax as 0.89.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hydrometer test was conducted on the material passing sieve No, 200 and the results are listed in the table below, The results of sieve analysis on the soil showed that the percentage passing No. 4 was 90 % and that passing No. 200 was 20 %. Estimate the clay size fraction in the soil. Table : Results of hydrometer test diameter (mm) 0.0700 0.0400 0.0150 0.0020 % finer (combined) 19 finer 95 80 16 65 13 45 0.0010 30 6 Select one:
A liquid limit test on a clay was performed with the following results. The natural water content of the clay is 38% and plastic limit is 21%. Number of Blows 6 12 20 28 32 Water content (%) 52.5 47.1 42.3 38.6 37.5 What is the liquidity index of this clay? (Use Interpolation) Group of answer choices 0.895 0.96 1.08 0.90 Please answer this asap. For upvote. Thanks
A sample of clay was coated with paraffin wax and its mass, including the mass of wax, was found to be 697.5g. The sample was immersed in water and the volume of the water displaced was found to be 355 mL. The mass of the sample without the wax was 690g and the water content of the representative specimen was 18%. If specific gravity of soil solids and the wax is 2.7 and 0.89 respectively, solve for the degree of saturation.
In a sieve analysis test, 95.5% of the sample is passing the 5mm sieve and 5.13% is passing sieve #200, which of the following is correct about this sample: O There is no clay in the sample ) the percent of silt and clay is: 5.13% There is 4.5% Sand and Gravel in the sample O 95.5% of the sample is Sand and Silt O O
Problem#1: An undisturbed sample of silty sand was brought to the laboratory at its natural water content, and the following measurements were made: Total mass at the natural water content: 1523.6g Mass of oven-dried sample: 1318.3g Total volume of sample: 728.2cm3 Density of the mineral solids: 2.7g/cm3 Calculate the porosity n, void ratio e, volumetric water content 0 and dry bulk density pb.
7. The following data was obtained from laboratory tests for a cohesive specimen: moisture content, w, was 22.5%; G=2.60; and to determine the approximate unit weight, a sample having a mass of 224.0 g was placed in 500 cm³ container with 382 cm³ of water required to fill the container. a. What is the Total Unit Weight of the soil sample in kN/m³? b. What is the Dry Unit Weight of the soil sample in kN/m³ ? c. What is the void ratio?
A liquid limit test on a clay was performed with the following results. The natural water content of the clay is 38% and plastic limit is 21%. Number of Blows 6 12 20 28 32 Water content (%) 52.5 47.1 42.3 38.6 37.5 What is the plasticity index of this clay? (Use Interpolation) Group of answer choices 15.74% 18.99% 18.85% 17.63% Please answer this asap for upvote. thanks
A 35 cc volume of core sampler was used in bulk density determination. The fresh soil in thesampler collected in the field weighed 83.5 g was oven dried. After 24 hours of oven drying thesample at 110oC, 20 grams of moisture were removed. Calculate the following: a. Bulk density b. Moisture content at weight basis and volume basis c. Percent pore space if the particle density is 2.63 g/cc d. Percent pore space filled
A dry sand is placed in a containerhaving a volume of 0.0089 cm3. The dry weight of the sample is 0.014 grams. Water is carefully added to the container so as not to be disturbthe condition of the sand. When the container is filled, the combined weight of the of soil plus water is 0.0174 grams. With this, find the void ratio, the porosity, the water content, the specific gravity thepertinent unit weights of the soil sample.
A 627-g sample of sand was found to have the following amounts of material retained on each sieve/pan: 3/8 in. = 22 g, No. 4 = 45 g, No. 8 = 96 g, No. 16 = 122 g, No. 30 = 163 g. No. 50 86 g, No. 100 = 51 g, No. 200 = 30 g, pan = 11 g a. Calculate the fineness modulus of the sand. b. Is this sieve analysis valid for acceptance purposes? Explain why. c. Does the sand meet the particle size criteria of ASTM C 33. Fully justify your answer (list and check all relevant criteria from ASTM C33)
Homework 7: A cylindrical clay sample of 38 mm in diameter and 76 mm in height. It was brought from the site and it had a total weight of 168 gm, and when dried in the oven, the weight was 130.5 gm. If you know that the specific weight of solid grains is 2.73. Find the moisture content, dry density, voids ratio, porosity, degree of saturation, total density, air content, and air gap ratio.
A compaction test was conducted in the laboratory and the following information was obtained: • The weight of the compacted soil specimen (including the mold) was determined to be 3815 • The volume of the mold = 1/30 ft³ (944 cm³) • The weight of the mold = 2050 g • The water content in the soil was determined to be 9.1% Find the dry unit weight of the soil (in units of kN/m³).