A rectangular beam has a width of 400 mm, and effective depth d=700 mm to centroid of tension steel bars. Tension steel reinforcement consist of 4436mm in two rows, compression reinforcement of 2022mm. Calculate the design moment strength of the beam, where f'c-21 Mpa, fy=420 Mpa, d'=65mm. (Mu-927 kN.m Ans)

A rectangular beam has a width of 400 mm, and effective depth d=700 mm to centroid of tension steel bars. Tension steel reinforcement consist of 4436mm in two rows, compression reinforcement of 2022mm. Calculate the design moment strength of the beam, where f'c-21 Mpa, fy=420 Mpa, d'=65mm. (Mu-927 kN.m Ans)

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in the weak direction at a point 4.1 m from the top. Use X- 4.8 m K 1 for both directions. X+Y Properties of W 12 x 65 A 12323 mm2 - 134.11 mm ry 76.71 mm Fy- 248 MPa Determine the allowable compressive strength (kN).
A beam has a width of 300 mm and an effective depth of 480 mm strength Pc= 34 MPa. Steel yield strength fy=415 MPa. The section is to be reinforced for tension only and the effective concrete cover is 70 mm. Deadload moment is 140 kN-m and the liveload moment is 180 kN-m. Use 2010 NSCP with t= 0.005. A. What is the governing steel ratio? B. What is the maximum number of bars needed for a 25mm diameter reinforcements? C. What is the minimum number of bars needed for a 25mm diameter reinforcements?
... Determine the nominal axial compressive strength, Pn for the following cases: a. L= 15 ft b. L = 20 ft Note: Pinned both end support W10 × 33 A992 steel r = 1.94 in E = 29000 ksi Fy = 50ksi L a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answer
USE NSCP 2010 A rectangular beam reinforced for both tension and compression barshas an area of 1450 mm² for compression bars and 4350 mm² fortension bars. The tension bars and compression bars are placed at a distance of 600 mm and 62.5 mm respectively from the top of thebeam. The beam width 300 mm, fc’ = 21 MPa, fy = 415 MPa andtension steel covering is 60 mm.If it is 8 m-simply-supported beam that carries three concentratedservice live loads P applied at three quarter points of the beam (exceptat the supports), neglecting the self weight of the beam, determine themaximum value of service load P in kiloNewtons.
W3D 25 Y= 155 %31 1oow= 2500 KN 27=310mm X= 475 Z= 60 %3D 102=600mm
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm bars.A. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions Note: Kindly double check your answer
1. A steel column 10 m long is fabricated from a W and C section arranged as shown. Determine the safe compressive load. Fy = 248 MPa, E = 200 GPa. Use AISC/NSCP Specs. C 310 x 45 y1=x=17 y2 d1 10 m W 200 x 46 a) Both ends of column are fixed b) Both ends of column are hinged c) One end fixed, the other end hinged Use design values of k. C 310 x 45 A = 5690 mm? d = 305 mm bf = 80 mm tf = 12.7 mm tw = 13 mm Ix = 67.3x10° mm ly = 2.12x10° mm x = 17 mm W 200 x 46 A = 5860 mm? d = 203 mm bf = 203 mm tf = 11 mm tw = 7.2 mm Ix = 45.5x10° mm ly = 15.3x10° mm
A beam is loaded with the following service loads: Moment due to Dead Load = 282 kN-m Moment due to Live Load = 330 kN-m Section: b=33 cm and d=57 cm. Material properties: f'c-30 MPa and fy =420 MPa Use rhomax = 0.019 for all calculations If required, compression reinforcement centroid is located 70mm from extreme compression face Calculate the the sum of the tension and compression reinforcements (if required) in mm² Use NSCP2015. Consider the displaced area of concrete. Answer in 2 decimal places.
AT:Design the steel reinforcement for flexural for the beam shown in the kN fig.below The dead load on the beam is 100 (not include self weight) & the live load is 200KN. useØ25mm& Use effective cover in top& bottom=60mm, use fc' = 27.6 Mpa, fy= 414Mpa. Ptive=200KN kN D.L= 100 d= 550mm 275mm 3m Зт
1. A steel column 10 m long is fabricated from a cover plate and C section arranged as shown. Determine the safe compressive load. Fy = 248 MPa, E= 200 GPa. Use AISC/NSCP Specs. 450 mm -cover plate 'I 12 mm y2 IP d2 10 m C 310 x 37 A = 4720 mm? d = 305 mm bf = 77 mm tf = 12.7 mm tw = 9.8 mm C 310 X 37 a) Both ends of column are fixed b) Both ends of column are hinged c) One end fixed, the other end hinged Use design values of k. tw d=305- Ix = 59.9x10° mm ly = 1.85x10° mm x = 17.1 mm x=17.1
Calculate the design moment strength for the reinforced concrete beam section shown below. f. = 24 MPa and f, = 415 MPa . 300 mm 5-D28 50 mm di = 812.5 mm
PERFORMED AS REQUIRED. SHOW YOUR COMPLETE SOLUTION. 4.3-1 Use AISC Equation E3-2 or E3-3 and determine the nominal axial compressive strength for the following cases: a. L = 10 ft b. L=30 ft L W10 x 100 A992 steel FIGURE P4.3-1