a) Find the controlling load path and corresponding net area, A², for rupture. The connection utilizes an L4x4x1/2” angle and 3/4” bolts with standard holes. O 2" 2⁹⁹ 2" 2" 1.5" 2.5" #1 2.5" 1.5" b) Now the same angle examined in Part a) is connected to a plate, but only through three bolt holes on a single leg. Find the design strength of the angle considering gross section yielding and net area rupture.

a) Find the controlling load path and corresponding net area, A², for rupture. The connection utilizes an L4x4x1/2” angle and 3/4” bolts with standard holes. O 2" 2⁹⁹ 2" 2" 1.5" 2.5" #1 2.5" 1.5" b) Now the same angle examined in Part a) is connected to a plate, but only through three bolt holes on a single leg. Find the design strength of the angle considering gross section yielding and net area rupture.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer it asap for an upvote. Thankyou. An A992 steel plate (12mm thick, in yellow) is connected to another A992 steel plate (12mm thick, in gray) using four bolts having a diameter of 33mm. If "x" makes the net width along bolts 1-2-4 equal to that of the net width along bolts 1-2-3-4; Compute the design tensile fracture capacity using the most critical net area (in kN).
Consider the following bolted connection. Slippage is permitted. Member: L6x6x3/4 3/16 “ gusset plate Pu Pu A36 steel 3.5* 1"diameter A325-X bolts 1 1/4" 3 " 3* 1 1/4" Question 3.1: Please, indicate if the combined bolt shear strength is closer to: Question 3.2: Please, indicate if the combined bolt bearing strength is closer to: Question 3.3: Please, indicate if the angle yielding strength is closer to: Question 3.4: Please, indicate if the angle fracture strength is closer to: Question 3.5: Please, indicate if the angle block shear strength is closer to: Question 3.6: Please, indicate if the overall connection strength is closer to:
3. Determine the design capacity using LRFD and NSCP-AISC specifications for the connection shown. Determine the critical net area. Show at least 3 rupture paths for comparison Show complete solution. Neglect block shear. Usę A572 Grade 42 steel and dl6 bolts on standard holes and gages. 75 75 75 Pu OR PA -8mm -10mm Pu OR PA 008 007
Design a connection for the following conditions: 2L 8x6xtension member • Dead load = 50 kips, live load = 100 kips, and wind load = 45 kips • Group A bolts, no slip permitted • 3/8-inch-thick gusset plate • A36 steel for both the tension member and the gusset plate • Length = 20 feet Provide a complete sketch showing all information needed for the fabri- cation of the connection. a. Use LRFD. b. Use ASD.
a] Compute LRFD 6.) Compute ASD CIVIL STEEL DESIGN ENGINEERING- BOLTED CONNECTION Sample Problem 5: The 175 x 100 x 16 mm angle shown connected to a gusset plate with three 25 mm bolts (A490) when threads are excluded from shear planes. The angle consists of A36 steel. Properties of 4 175 x 100 x 16 A36 Steel Properties of A490 bolts A = 4181 mm² t = 16 mm Fy = 248 MPa F₁ = 400 MPa Fy = 276 MPa Nominal hole dia. = 27 mm 75 T+ 100 Gusset Plate 100 F 100
2. Consider the connection on the following angle L7 x 4 x О О О 1.5 3" 3 + 3 3 + + + Use preferred material for L. All bolts are 1" A-490-X bolts. Edge distance is 1.5”. a) Determine the nominal bolt capacity. b) Determine the nominal bearing capacity for each plate. c) Determine the nominal rupture capacity of each plate. d) What is the nominal capacity of the connection?
Hhello, Thanks a lot for your help, please I have the following points: 1-Is it allowed to use Fult=65 ksi? 2-Why we consider Wt section? this procedure as I understand is applied when the connection is to flange. 3-The net area estimated is only for one bolt, i believe An=11.80-(4*7/8*0.305)=10.733 inch^2. 4-x bar which I consider is from case 2 only since case 7 will not work, x bar is only Tw/2 value?. U value=1-(0.1525/6.50)=0.977. Could you please advise? Thanks.
Question 12. Determine the net area (An) and effective net area (A) for the channel tension member shown below. Assume bolt diameter is 5/8 in. The section is C6x10.5 (A36) (- 1½" lapttp 4@2" le ole ole ole o o ob O Ос
CLO3: Determine the tensile capacity of the 1/2-in. by 7-in, plate shown in Figure bellow. The connection is made with 6/8-in.-diameter bolts, the plate is ASTM A529, grade 50 (Fy" 50ksi, Fu= 65ksi). Neglect block shear. 7" Tu 1/2" x 7" plate Oa. 127.97 kips Ob. 180.31 kips Oc 157.50 kips Od. 126.88 kips
a rivet lap joint is shown. The rivets used have allowable shear strength equal to 533 MPA with diameter of 16mm. The steel plate has a yield strength equal to 275 MPa and ultimate strength equal to 340 mpa; 300 mm wide and 16 mm thick. Determine the safest value of P that the connection can resist. Use NSCP, assume additional 1.6mm for the rivet hole. Neglect block shear
Question 17 2L5x3x7mm tension momber is connocted to a gussot plate by 16-mm-diameter bolts as shown in the figure, Given that e= 30 mm, s= 50 mm, Fy =345 MPa and Fu=402 MPa, caicukato the following 2 L5 x3x % LLBD (two angles, long legs back-to-back) A242 stoel 60 mm e (am) (mn) e (mm) 55 Not area in shoar for a single angle under block shear lailue, Ariv mm? 56. Not area in tension for a single anglo under.block shoar failuto Arit = 57. Norninal block shear strongth in kN of the double angle Use Ups 10, Pn INPUT ALL ANSWERS AS WHOLE NUMBER
Q 1-: The slip-critical connection shown below consists of four grade A490 3/4-in- diameter bolts, in standard holes, with threads excluded from the shear planes. The angles and gusset plate have Class A faying surfaces and are fabricated from steel with a tensile strength of Fu -65 ksi. Assuming that the angles and gusset plate are satisfactory, determine the shear force that may be applied to the bolts in the connection. 1/2" plate P 4 x 4 x 1/2" angles 3@3" 2"- 2"