A 12-m long horizontal beam is loaded by a downward distributed load which decreases from 20kN/m @ A to 0 kN/m at B, a 80 kN point force at D, and an 102 kN·m concentrated couple @ A.The reactions at B and C have been solved for you. Draw the shear and moment diagrams forthe beam. Show your work and include the values and locations of every minimum, maximum,and inflection point.Values to check your graphs: Vmax = 80 kN between C and D, Mmax = -240 kNm @ C20 kN/mA102 kNm6 m>M26 KNBC114 KN3 m3 m80 kN

Answered: A 12-m long horizontal beam is loaded…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam is supported at both ends. It carries two concentrated load of 110kN, a clockwise moment of 110kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 60GPa. Solve the following if the reaction at point B is 328.90256410256kN, upward. BEAM DIMENSION: Width = 190mm , Height = 390mm NOTE: b = 4.8m ; Determine the deflection at midspan
A rectangular beam is supported at both ends. It carries two concentrated load of 190KN, a clockwise moment of 160KN- m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 150GPA. Solve the following if the reaction at point B is 309.63888888889KN, upward. USE ANY МЕТНOD BEAM DIMENSION: Width = 130mm , %3D Height = 460mm %3D NOTE: b = 4.2m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) P W M 1m 1m 1m Determine the deflection at midspan
Consider the beam shown below. Take P = 5 kip and w = 1.7 kip/ft. Point E is just to the right of the 5-kip load. Follow the sign convention. a) Determine the normal force at point E. Express your answer in kilopounds to three significant figures. b) Determine the shear force at point E. Express your answer in kilopounds to three significant figures. c) Determine the moment at point E. Express your answer in kilopound-feet to three significant figures.
The compound beam is subjected to a uniform dead load of 380 lb/ft and a uniform live load of 285 lb/ft. Assume B is a pin and C is a roller. Follow the sign convention. (Figure 1) Figure A 5 ft 00 B 5 ft D 5 ft C 1 of 1 Part A Determine the negative bending moment at A with the maximum magnitude. Express your answer using three significant figures. ΠΑΣΦ (MA)max(-) = Submit Part B (VD) max(+) Request Answer Determine the maximum positive shear at D. Express your answer using three significant figures. Submit = ΑΣΦ ↓↑ vec Request Answer vec ? ? k.ft lb
A rectangular beam is supported at both ends. It carries two concentrated load of 30kN, a clockwise moment of 150KN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 130GPA. Solve the following if the reaction at point B is 256.73846153846KN, upward. BEAM DIMENSION: Width = 130mm, Height = 360mm NOTE: b = 4.8m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) w What is the numeric value of C1 (1st Constant)? kN-m2 Determine the deflection at midspan.
A structural steel wide-flange shape [E = 280 GPa; I = 310 x 106 mm4] is loaded and supported as shown. A uniformly distributed load of 25 kN/m is applied to the beam, causing the roller support at B to settle downward (i.e., displace downward) by 2.8 mm. Determine the reaction at support B.[LAB = 5.1 m, LBC = 1.5 m] W A Answer: LAB KN B gap LBC C
A distributed loading of p = (800x ) Pa acts over the top surface of the beam shown . Determine the magnitude and location of the equivalent resultant force.
Week 5, Question 2: Using the force method, calculate the bending moment at B for the statically indeterminate frame below. Please ignore the axial and shear deformations. Take a 12 kN and L = 5.5 m. a B EI A 2EI -3 m Calculate the bending moment at B: kN m MB 2EI m D EI E +=+ L
Example The beam ABC is loaded via a 500 N.m couple and a 600 N force as shown. ... The beam is connected to the rest of the system by a pin joint at B and a roller support at ... Determine the magnitude of the reaction forces on the beam at the supports.
Replace the distributed loading with an equivalent resultant force, and specify its location on the beam measured from point A. Please see the figure in the following picture.
The figure shown is a beam subjected to varying loadings and a point load.a) Determine the magnitude and direction of the single equivalent force to the forcing systemshown. Specify its location on the beam from point B.b) Calculate for the support reactions at A and B.
A fixed crane with a mass of 2000 kg uses a stainless steel cable (Yield Strength =210 MPa) to lift a 2400 kg mass. The center of the gravity of the crane is located at G and ean be used to model the weight of the crane at a single point. • Determine the reactions at A and B • Determine the minimum diameter that the cable should be to lift a 2400 kg object for the given erane using a factor of safety equal to 2.5. 2400 kg 1.5 m B +2 m- 4 m-

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS