Answered: A 10 pole lap wound DC armature has a…

A 10 pole lap wound DC armature has a total of 200 conductors each with a current carrying capacity of 10 A. The average induced emf per conductor is 10 V. The power rating of the DC machine is

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.1MCQ: The Ohms law for the magnetic circuit states that the net magnetomotive force (mmf) equals the...

See similar textbooks

Related questions

Q: 2. DC Motor has 100 mWeb/pole of flux, 120 no. of conductors, 4 field poles, and it has wave winding…

A: Given a DC motor has, Flux per pole, φ=100 mWbpole Total number of conductors, Z=120 Total number of…

Q: Example with 778 wave-connected armature conductors and run- ning at 500 rp.m. supplies a lood of…

A: Since there are multiple questions uploaded so solving the first question accordingly as per the…

Q: Q4. a) Figure 4 depicts a simple DC motor, its armature winding consisting of a single turn of…

A: A DC motor is a Electric device which converts the electrical energy into physical motion. The…

Q: A 230V dc series motor has an armature resistance of 0.5 and 0.3 oh respectively. The motor draws a…

A: Case 1: Without diverter: The motor can be represented as below Here Vin=Motor voltage…

Q: Q4. a) Figure 3 depicts a simple DC motor, its armature winding consisting of a single turn of…

A: We need to answer the above three questions regarding a DC motor.

Q: Q3. B. what are the features of Wave winding of DC machine?

A: The answers to both parts are as follows.

Q: 4) A dc. ahunt machine while running as generator develops a voltage of 240 V at 1000 rp.m. on…

A: In this question we will find speed and efficiency of motor with given data....

Q: 2) the armature windings of a 12-pole DC machine are composed of 72 coils with 10 windings, and the…

Q: The DC shunt generator with the terminal voltage 350 V, armature drop 9 V and the each brush drop 4…

A: We need to tell about generated voltage for generator.

Q: A 4 pole armature of a DC machine has 175 conductors and a flux per pole of 0.1 wb. Find the EMF…

A: Given a DC machine having, Number of poles, P = 4 Number of conductors, Z = 175 The flux per pole,…

Q: The DC shunt generator with the terminal voltage 375 V, armature drop 9 V and the each brush drop 2…

A: As per the guidelines of Bartleby we supposed to answer first question only since both question are…

Q: Q2) In DC machine, the speed is 800 RPM, the flux per pole is 2 m wb, and it has a Lap winding…

A: Given: In a DC machine Speed, The flux per pole, It has Lap winding (means the number of parallel…

Q: An 2 pole, wave connected armature has 550 conductors and its generated e.m.f is 110 V. If the…

Q: A 250 V DC shunt generator has a constant loss of 1250 W. Find the load current for maximum…

A: Solution: Shunt generator; V=250 v, Constant loss =1250 W, Find the load current for maximum…

Q: 1. A four-pole, lap wound DC machine is having 500 conductors on its armature and running at 1000…

A: Note: We are authorized to answer one question at a time since you have not mentioned which question…

Q: The armature of a 4-pole dc machine rotates at 840 rpm. The armature length and diameter are 40 cm…

A: Given data for a dc machine P=4 N=840 rpm l=40 cm d=30 cm ϕp=65mWb n=5 Average e.m.f. induced in the…

Q: A 220V series generator has an armature resistance of 0.4ohms. If the generated emf is 230V and the…

Q: Determine the power output of a DC armature having 1152 lap connected conductors carrying 150 A and…

Q: The DC shunt generator with the terminal voltage 350 V, armature drop 7 V and the each brush drop 2…

Q: A four-pole, 24 KW, 120 V, DC machine has a Duplex LAP-wound armature which has 80 coils with 10…

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: The DC shunt generator with the terminal voltage 300 V, armature drop 7 V and the each brush drop 4…

A: In this we will find emf..

Q: - A Dc shunt generator produces 445 A at 250 V, the resistance of shunt field circuit and armature…

A: Given data: Terminal Voltage, Vt = 250 V Shunt field resistance Rsh = 50 Ω Armature resistance Ra =…

Q: The DC shunt generator with the terminal voltage 325 V, armature drop 9 V and the each brush drop 4…

Q: An 8-pole dc generator has a duplex lap wound armature with 64 coils and 16 turns per coil. The…

A: Ther are a total of 64×16=1024 turns on the armature of this machine, so the number of turns per…

Q: Outline with the aid of a suitable diagram the necessary power conversion stages required to…

A: Question in part b is independent to that of part c and d. We are authorized to answer one question…

Q: The DC shunt generator with the terminal voltage 300 V, armature drop 8 V and the total brush drop 2…

Q: A 10 pole, 400 kW, 250 V, dc generator has a lap wound armature with 75 slots each having 12…

Q: A 4-pole, 440 V, 900 rpm, simplex wave wound dc motor has a full load armature current of 25 A. The…

A: given simplex wave wound dc motor

Q: Q3 (а) Describe a single wire DC motor with the help of a diagram. (b) Illustrate the physical…

Q: The DC shunt generator with the terminal voltage 350 V, armature drop 6 V and the total brush drop 4…

A: A dc shunt generator V=350V Armature drop=6v Brush drop= 4v

Q: ii. Differentiate the two types of armature windings in DC machines: lap winding and wave winding.

Q: A 4-pole dc motor has a wave wound armature with 800 conductors. The useful flux per pole is 20mWb.…

A: In this question, A 4-pole dc motor wave wound armature so Number of parallel path A= 2 Z=800…

Q: - A Dc shunt generator produces 445 A at 250 V, the resistance of shunt field circuit and armature…

Q: The armature of a 4-pole dc machine is rotating at 840 rpm. The armature length and diameter are 40…

Q: Q3) The armature of a 4-pole DC machine has 240 coils wound in lap formation. Each coil generates a…

A: P=8 , Z =240 , lap wound A=P Ecoil=NPZϕ60=4 Icoil=5A a) Eg=NPZϕ60A=44=1 b) IP=5IA=IPA=54=1.2 c )…

Q: The 4-pole direct current electric machine works as a motor. In this direct current machine, which…

A: The direction of flux at the main pole: The direction of the flux at the main poles is the same as…

Q: A six-pole, 24 KW, 120 V, DC machine has a Duplex LAP-wound armature which has 72 coils with 12…

A: Pole=6 Coil=72 12 turns per coil Resistance per conductor=0.04ohm Lap wound , total no. of parallel…

Q: When the DC machine is running under saturation condition, then flux per pole decreases due to…

A: Ans. True

Q: The DC shunt generator with the terminal voltage 350 V, armature drop 7 V and the total brush drop 4…

A: Given that Terminal voltageVt = 350v Armature voltage drop Va= 7v Brush dro VB = 4v

Q: An 4 pole, wave connected armature has 520 conductors and its generated e.m.f is 115 V. If the…

A: Need to find flux

Q: The DC shunt generator with the terminal voltage 300 V, armature drop 8 V and the each brush drop 2…

Q: .72 At 1200 rpm the induced emf of a dc machine is 200 V. For an armature current of 15 A the…

A: we need to find out torque.

Q: A 4 pole armature of a DC machine has 175 conductors and a flux per pole of 0.1 wb. Find the EMF…

A: P=4Z=175ϕ=0.1 wbN=600A=P (lap wound)

Q: The DC shunt generator with the terminal voltage 375 V, armature drop 8 V and the each brush drop 2…

A: Generator: It is an electromechanical device, that converts the mechanical energy to electrical…

Q: A 4-pole DC generator has 800 armature conductors and a flux per pole of 10 mWb running at 600 rpm.…

A: Given, A DC generator with simplex lap winding has, Total number of pole, P = 4 Total number of…

Q: A DC shunt machine while running as generator develops a voltage of 250 V at 1000 r.p.m. on no-load.…

Q: A DC machine has 536 conductors connected as a lap winding at its armature. The machine has 6-pole…

Q: An 8-pole DC machine has a simplex wave-wound armature containing 200 coils of 10 turns each. The…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: 55. Calculate the voltage induced in the armature winding of a 4-pole, lap wound, dc machine having…

Q: The DC shunt generator with the terminal voltage 375 V, armature drop 6 V and the each brush drop 4…

A: In this question , we will find generated emf in dc machine.

Concept explainers

DC Generator

An electromechanical machine which converts input mechanical energy to respective output electric energy is called a generator.

Question

A 10 pole lap wound DC armature has a total of 200
conductors each with a current carrying capacity of 10 A.
The average induced emf per conductor is 10 V. The power
rating of the DC machine is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A DC generator has an armature emf of 500 V when useful flux/pole is 20 mWb, and a speed of 625 rpm. The generated emf at a speed of 125 rpm and same flux is
A dc machine has hysteresis loss of 300 W and an eddy current loss of 200 W when running at 1200 rpm. At what speed will the total core losses be a quarter of the original if the flux is to be twice as the original.
In a 2 pole lap winding dc machine , the resistance of one conductor is 2Ω and total number of conductors is 100. Find the total resistance.
10. A potential difference of 250 V is applied to a field winding at 15-C and the current is 5 A. What will be the temperature of the winding when current has fallen to 3.91 A applied voltage being constant. Assume temperature coefficient at 15'C is equal to 1/254.5 per °C
Iron losses in a DC machine are independent of variations in ) load voltage speed O All of these
The path of a magnetic flux in a transformer should have O High resistance O Low reluctance O Low resistance O High reluctance
What are the rotating parts on d.c machine. commutator segments O brushes O inter-pole O pole shoe
A three-winding transformer is connected to an AC voltage source as shown in the figure. The number of turns is as follows: N₁ = 100, N₂ = 50, N3 = 50. If the magnetizing current is neglected, and the currents in two windings on secondary side are 2230° and 22150°, then what is the value of the primary current in Ampere? I 0000000000- N₁ № ₂ Z 00000 00000 Z N3 H I₁₂ I₁₂₁ ¹3
The voltage induced in 8 poles lamp wound generator is 120 V with armature resistance = 0.3 2. What will be the terminal voltage at a load = 3.6 A when the machine is rewound as a wave?
An 8-pole DC machine has a simplex wave-wound armature containing 200 coils of 10 turns each. The resistance of each turn is 0.01 Ω. The flux per pole is 0.004 Wb. what is the internal resistance of the armature in ohms?
Magnetic Field of Single Coils / Biot-Savart’s Law
AC Machinery Fundamentals A three-phase delta-connected six-pole winding is installed in 36 slots on a stator. There are 150 turns of wire in each slot of the windings. All coils in each phase are connected in series. The flux per pole in the machine is 0.060 Wb, and the speed of rotation of the magnetic field is 1000 r/min. What are the resulting phase and terminal voltages?