8. Given this two-port representation of an op amp with stage 1 being the diff pair, stage 2 being the middle gain, and stage 3 being the output circuit, calculate the overall voltage gain from Vsig to load RL. Ro1 I Av1'Vin1 Ro2 Av2*Vin2 Rsig RI2 RI3 Ro3 Av3*Vin3 |RL Vsig Rsig=120 Ohms, Ri1=2k, Av1=30, Ro1=1k, Ri2= 5k, Av2=200, Ro2=1k, Ri3=200k, Av3=0.9, Ro3=140 Ohms and RL = 100 Ohms

8. Given this two-port representation of an op amp with stage 1 being the diff pair, stage 2 being the middle gain, and stage 3 being the output circuit, calculate the overall voltage gain from Vsig to load RL. Ro1 I Av1'Vin1 Ro2 Av2Vin2 Rsig RI2 RI3 Ro3 Av3Vin3 |RL Vsig Rsig=120 Ohms, Ri1=2k, Av1=30, Ro1=1k, Ri2= 5k, Av2=200, Ro2=1k, Ri3=200k, Av3=0.9, Ro3=140 Ohms and RL = 100 Ohms

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 741C is an op-amp with Aol = 100,000 and a minimum CMRRAB = 70 dB. What is the common- mode voltage gain? If a desired and common-mode signal each has a value of 5 µuV, what is the output voltage? Show the details of your work.
In the voltage regulator circuit shown in the figure, the op-amp is ideal. The BJT has VBE=0.7 V and Beta = 100, and the Zener voltage is 4.7 V. For a regulated output of 9 V, the value of R (in Ohms) is Express answers in two decimal points. Show solution on your answer sheet. V = 12 V Vo = 12 V 1 k2 1 k2 AV2 = 47 V %3D ww
O cathode O focusing anode The of an instrument is a measure of how close the output reading of the instrument is to the correct value. In OP-AMP, signal applied to the inverting input gets amplified and obtained as the inverted signal at the output. dows
The two input terminals of an op-amp are connected to voltage signals of strength 745µV and 740µV repectively. The gain of the op-amp in common mode is 50 and CMMR is 8&IB. Calculate the output voltage and % of error due to common mode.
For the given op-amp circuit, determine: in/ls, Vout/in, and Vout/Is. RI iin Is Vout RL ZinCL) Zout(CL) For the op-amp: AVOL=2000, Rin=100KN, Rout-502 Rs-502, RI-5002, RL=1002
Create Op-amp circuit... with:Vin= -1 Volt (DC) Vout = 14 Volt (DC) Only resistors with 1k, 3k, 5k, 7k and 11k ohms can be used while the circuit is being built. The V+ value of the LM741 IC to be used for op-amps will be 20 volts and the V- value will be -20 volts. You need to use at least one inverting amplifier and one non-inverting amplifier to build the circuit. Question: Write the gain formula of the circuit and calculate it, and write how we should find the Vout value..
Q3. This question is on op-amps. (a) Comment on the differences between the values in the two columns of properties in the table for both an ideal op-amp and a typical 741 op-amp. Fill in the two missing values. Op-amp Gain Input resistance Unity Bandwidth Short circuit current Output resistance Ideal Infinite Infinite Infinite 0 741 200000 1MHz 25mA 75 ohms
1- a) Draw the circuit of a V-I converter and derive an expression for the output current in terms of input voltage. b) Draw the neat diagram of analog multiplier using log-antilog amplifiers and explain its operation
the output of an op amp is affected by the input offset voltage,input offset current, input biassing current , the power supply,input frequency?? ( true or false) and why ?
The two input terminals of an op-amp are connected to voltage signals of strength 754µV and 740µV repectively. The gain of the op-amp in differential mode is 50 and CMMR is 80 dB. Calculate the output voltage and % of error due to common mode.
An inverting op amp has Rf= 600kohm and R1= 6kohm. Determine the op amp circuit voltage gain, input resistance and output resistance. Also Determine the output voltage and input current if the input voltage is 0.1 V. Assume op amp to be ideal one.
An op-amp has a differential voltage gain of 2000 and a CMRR of 20000. A single-ended input signal of 250 uVrms is applied and a 0.5Vrms, 50 Hz common-mode noise sigmal appears on both inputs from the ac power line. Calculate the output voltage. Choices: a) 0.5Vrms, b) 0.7Vrms, c) 0.75Vrms, d) 1.5Vrms