100 MHz carrier wave has a peak voltage of 5 volts. The carrier is frequency modulated (FM) by a sinusoidal modulating signal or waveform of frequency 2 kHz such that the frequency deviation Af is 76 kHz. The modulated waveform passes through zero and is increasing at t= 0. Determine the expression for the modulated carrier waveform.

100 MHz carrier wave has a peak voltage of 5 volts. The carrier is frequency modulated (FM) by a sinusoidal modulating signal or waveform of frequency 2 kHz such that the frequency deviation Af is 76 kHz. The modulated waveform passes through zero and is increasing at t= 0. Determine the expression for the modulated carrier waveform.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

drive a formula for (SNR) of sinusoidal signal has been sampled and quantized.
In an Amplitude Modulator where the carrier and modulating signals are both sine waves, the frequency spectrum of the resulting AM signal is shown below. 10V 2V 2V kHz 803 808.6 a) Determine the equation of the modulating signal b) Calculate the bandwidth of the AM signal c) Calculate the effective current of the AM signal thru a 75-ohm load. d) Sketch the AM wave and label the maximum and minimum voltage of the signal.
Using MATLAB. Generate a square wave signal whose peak amplitude is 1 V, frequency of 1000 Hz, and 50% duty cycle. Use a sampling rate of 20000 Hz and a duration of 1 s. Plot the signal for a duration of 5 ms. Please help by giving the code. Thank you
In the square wave signal in the figure, the duration of 1 is 0.6ms and the period is 1ms; a) What is the average DC value of the signal? b) Interpret the given signal equation? c) 1.2. and amplitude values of the 3rd harmonic signals. Calculate, draw the frequency spectrum. d) Draw the frequency domain.
The carrier frequency is 600 Hz, and the modulating signal is a single-tone sinusoidal signal. The x-axis is in time while the y- axis is the amplitude of the AM signal. If the peak voltage level of modulating and 1v and signal respectively, determine the modulating index. the carrier are 2V 2 1.5 1 0.5 -0.5 -1 -1.5 -2 0.005 0.01 0.015 0.02 0.025 0.03 0.035 0.04 0.045 0.05 Time (s)
Consider FM wave with a sinusoidal wave of frequency fm as the modulating signal, and assume a peak frequency deviation Af. Determine the average power of the modulating signal (assume antenna resistance 1 ohm)
2. Write an OCTAVE program to plot the signal given below. P- Pmax Sin(21Ift); where Pmax= 10 MW, -60 Hz. %3D Find out time period and verify it with graph. Assume necessary data.
derive forirer components of square wave signal
a semi-crinlar currend wave nhich Defermine the PMS Value of has a manimum valse of a . (Nofe: the equatim of a gemi- Eramlar wave is ²t y" - a° ). %3D ta
1. (5) We have generated a PWM signal. In each period, the signal is in low state for 28.4 ms. The duty cycle of the signal is 29%. What is the frequency of this signal?
A carrier wave of 1 GHz and amplitude 3 V is frequency modulated by a sinusoidal modulating signal frequency of 500 Hz and of peak amplitude of 1 V. The frequency deviation is 1 kHz. The peak level of the modulating wave form is changed to 5 V and the modulating frequency is changed to 2 kHz. The expression for the new modulated wave from is
Problem 1 The Figure below shows a screen shot of a signal recoded by an oscilloscope. a) What are the average and fundamental frequency for the given signal? b) If the signal is sampled with a sampling frequency of 10 Hz, sketch the sampled signal on the same chart. c) Find the average value of the sampled signal. d) Use zero-order hold to convert the sampled signal to a continuous one and sketch your result on the same chart 2. 0.5 0.4 Time (s) 0.1 0.2 0.3 0.6 0.7 0.8 0.9