10.23: For the following electric circuit, find Z and Y (1200+j850)2 (1500+j900)parameters? Also, compute input and reflectedimpedancesandadmittances. (Ans.:(10K+j20K)saZ₁1-23.75/61.8°K2, Z₁2-Z21-22.1263.4°K2,Z22-23.9261.2°K2,K=0.065 Y₁1-0.321/-34°m,Y12-0.3-32°mu, Y21-0.065/-55.7°mu & Y22=0.319/-33.6°mu)

Answered: Image /qna-images/answer/b5ffce8f-2208-4ee4-b19b-4d46c99d80a1.jpg

10.23: For the following electric circuit, find Z and Y (1200+j850)2 (1500+j900) 2 parameters? Also, compute input and reflected impedances and (Ans.: admittances. Z₁2-Z21-22.1/63.4°K2, (10K+j20K) Z₁₁-23.75261.8°K2, Z22-23.961.2 KQ, Y₁₁-0.3214-34 mv, Y12=0.3-32°mu, Y21-0.0652-55.7°mu & Y22-0.319/-33.6°mu) 0.065-5

10.23: For the following electric circuit, find Z and Y (1200+j850)2 (1500+j900) 2 parameters? Also, compute input and reflected impedances and (Ans.: admittances. Z₁2-Z21-22.1/63.4°K2, (10K+j20K) Z₁₁-23.75261.8°K2, Z22-23.961.2 KQ, Y₁₁-0.3214-34 mv, Y12=0.3-32°mu, Y21-0.0652-55.7°mu & Y22-0.319/-33.6°mu) 0.065-5

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

Ac - 100 VrmsR1 - 1kR2 - 500Rload - 1kCapacitor - 2uF Q1. How much is the capacitor voltage lagging from the AC source
2-A resultant current is made of two components: a 10 A D.C. component and a sinusoidal component of maximum value 14.14. The average value of the resultant current is amperes (a) 0 (b) 24.14 (c) 10 (d) 4.14 and r.m.s. value is - amperes (e) 10 (f) 14.14 (g) 24.14 (h) 100
Lissajous Choose... Figures Done Choose... STEP UP THE CURRENT STEP UP THE VOLTAGE FREQUENCY PHASE DIFFERENCE
For the below sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 0.2ms/cm and the volt/cm switch is on 1 V/cm. a) the frequency will be Hz b) the r.m.s value will be In CRO the beam can also be shifted vertically by applving a suitable DC voltage to the
Reduce to its simplest form using msop
A step-down chopper is to be used to supply power from a 600-V overhead wire to the commutator motor on a trolley bus. The motor may be mod- eled as a generated direct voltage in series with a resistance of 0.2 and an inductance of 25 mH. The frequency of the chopper is set at 500 Hz. (a) When the bus is stopped, what should be the ON time of the chopper to provide a motor current of 150 A? (b) What is the maximum possible generated voltage of the motor for which a current of 150 A can be supplied? (c) What is the average value of the supply current for the conditions of (a) and (b)? បទៅនឹងរស់របស (d) If the motor current is to be continuous, what should be its minimum. value?
What impedance vector - j25 represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a resistance.
1) Suppose you have a sinusoidal input signal and wish at the output the signal should be same (in phase) as input signal but amplified then which circuit should you use? & WHY?? Draw the circuit diagram you would use.
2. For a sinusoidal voltage trace displayed by the CRO, the time/cm switch is on at 500µs/cm and volt/cm switch is on 5V/cm. The width of one complete cycle is 4cm and peak to peak height is 5cm. Find (a) the frequency, (b) peak to peak voltage, (c)the amplitude and (d) the rms value
The sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 50 µs/cm and the volt/cm switch is on 20 V/cm. The width of one complete cycle is 3.6 cm and the peak to peak height is 5.8 cm. Determine the following: The frequency is = The peak to peak voltage is = The amplitude is = The R.M.S voltage is =
What is the advantage of using square wave-form as an Input Signal? What is the shape of the outputwhen the input signals are sinusoidal and triangular in shape? (Hint: Use Function generator andOscilloscope to observe the output)
1. For a sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 500µs/cm and the volt/cm switch is on 5V/cm. The width of one complete cycle is 4cm and peak to peak height is 5cm. Find for the waveform a) the frequency, b) the peak to peak voltage, c) the amplitude, and d) the r.m.s value