Limiting states1. The MC describes the state of stress of our point in the field. That is, the MC shows us thevalues of the two principal stresses and the value of the maximum shear stress that thepoint is sustaining in the field. Consider a point in a geostatic soil mass. For our point, o'vo= 100 kPa and o'ho = 40 kPa. Take a sheet of paper and draw the Mohr Circle for this pointcarefully.2. Now, we know that o'ho is a principal stress because t = 0 on the vertical plane (in thefield). Similarly, o'vo is a principal stress because t = 0 on the horizontal plane (in the field).What is the value of t on the plane inclined 45 degrees clockwise from the horizontal? Goahead and use your drawn MC to find this value. The value should be t = 30 kPa.3. Note that the value found (t = 30 kPa) is the maximum shear stress that the point issupporting in the field, as it is under o'v = 100 kPa and o'h = 40 kPa. Consider now asituation in which o'h remains at 40 kPa, but o'y grows to 120 kPa. Draw this new MC onthe same graph you used to draw the MC for item #1 above. If you draw the second MCcorrectly, you will find that the maximum shear stress that the point is supporting is now40 kPa.4. You can now confirm that the maximum shear stress that a point in a geostatic mass feelsis equal to the radius of its MC, which is (o'v-o'h)/2. And so, the maximum shear stressdepends on how different o'v and o'h are. If o'v = o'h, then there is no shear stress felt bythe point (the MC is a point on the MC graph; on the x-axis).5. Neatly redraw the MC you drew earlier for a point with o'y = 100 kPa and o'h = 40 kPa.This time draw the MC in the space below.113

"Since you have posted a question with multiples parts, I will solve first 3 for you as per…

1. The MC describes the state of stress of our point in the field. That is, the MC shows us the values of the two principal stresses and the value of the maximum shear stress that the point is sustaining in the field. Consider a point in a geostatic soil mass. For our point, o'vo = 100 kPa and o'ho = 40 kPa. Take a sheet of paper and draw the Mohr Circle for this point carefully.

1. The MC describes the state of stress of our point in the field. That is, the MC shows us the values of the two principal stresses and the value of the maximum shear stress that the point is sustaining in the field. Consider a point in a geostatic soil mass. For our point, o'vo = 100 kPa and o'ho = 40 kPa. Take a sheet of paper and draw the Mohr Circle for this point carefully.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Plane AB is under pressure and Plane AB has an angle = 30 degrees to sigma = 50 nPa.a. Determine the equations used to calculate the normal and shear stress in the plane ABb. Draw a normal vector sketch on the plane AB and the angle formed between the normal vector andc. Calculate normal stress and shear stress in plane AB (Round up to 4 digits after comma)d. Plot the point normal stress and shear stress plane AB on the Mohr Diagram sketch.
2. The state of plane stress at a point is represented on the element shown in the figure below. (a) Determine the principal stresses acting on this point, and the corresponding orientation (angle). (b) Determine the maximum in-plane shear stress, and the corresponding orientation (angle). Also determine the associated average normal stress. (Do not draw Mohr's circle). 79 MPа 60 MPа
Question 2 Referring to the stresses on the surfaces of an element in Figure Q.1, determine : (a) principal plane and principal stresses (b) the maximum shear stress and the corresponding normal stress, and (c) the range of angle rotation q which give the value of shear stress txy, equal or less than 40 MPа. 30 MPа 80 MPa
In a triaxial stress system, the six components of the stress at a point are: 0x = 6 MPa Try = 1 MPa σyy = 5 MPa Ty₂ = 3 MPa σ = 4 MPa T₁ = 2 MPa Determine the normal and shearing stress on the plane whose direction cosines are 1/3, 1/3, 1/√√3. Also calculate the direction of the shear stress.
Determine the equivalent state of stress on an element if it is oriented 50° counterclockwise from the element shown. Assume that σ = -13 ksi and Txy = -19 ksi. Solve the problem using ox Mohr's circle. σχ F Part A Determine the normal stress ox'. Express your answer in kilopounds per square inch to three significant figures. ANSWER: = Tap image to zoom ksi Part B Determine the normal stress Øy'. Express your answer in kilopounds per square inch to three significant figures. ANSWER:
90 MPa 1. If a point is subjected to the state of stress shown in the figure, determine the principal stresses and the maximum in-plane shearing stress. Show all results using Mohr's Circle diagram. 40 MPa 30 MPa
EXAM QUESTION 2 The state of plane stress at a point is represented by the element shown in the figure. (Assume E=210 GPa, v=0.3). Determine a) the principal stresses and the oriented angle associated with the direction of each principal stress using the transformation equations of plane stress; and b) the absolute maximum shear stress at the point according to this stress matrix. 50 MPa 50 MPa 50 MPa
The state of plane stress at a point is represented by the element shown in Figure Q1. Construct a Mohr Cirele to determine a) the principal plane and the principle stresses, b) the maximum in-plane shear stress and the associated average normal stress, and c) the state of stress at the point on another element oriented 25° clockwise from the position shown. d) Show the orientation of the element stresses on an appropriate sketch for a), b) and c) 60 MPa 30 MPa 45 MPa Figure Q1
Q.2) A state of stress is specified as shown in Figure (2), By using Mohr's circle determine the normal and shearing stresses and their directions on: a- The principal planes? b- The planes of maximum shearing stress? c- The planes whose normals are at (+50°) and (+140°) with x-axis? show your results on complete sketches of differential elements. 80 MPa 50 MPa YA 40 MPa + 50 MPa, 80 MPa 40 MPa Figure (2)
For a plane stress problem, the state of stress at a point 'Q' is represented by the stress element as shown in figure. 20 MPa 25 MPa 80 MPa 80 MPa 25 MPa 20 MPa For this stress element, If Mohr's circle is drawn Find the maximum stree andd orinentation of plane
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and Sy = 230 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 49°. Sy 一 Answer: Sn = MPa Snt = MPa
Determine the principal stress, the maximum in-plane shear stress, and average normal stress. Specify the orientation of the max stress element in each case. Solve the question using Mohr Circle. OX = 41 gy = 41 x 2 EXy = 41 /2 %3D