1. The following table provides the displacement data for an Amott wettability test on three cores from a Tronoh reservoir in Perak: Displacement by Oil (mL) Displacement by Water (mL) Core No. Spontaneous Forced Spontaneous Forced 1 0.05 1.25 0.81 0.85 0.00 1.69 0.00 0.97 0.47 0.53 0.01 0.59 Calculate the Amott-Harvey wettability index for each core and explain the wetting characteristics of each core.

1. The following table provides the displacement data for an Amott wettability test on three cores from a Tronoh reservoir in Perak: Displacement by Oil (mL) Displacement by Water (mL) Core No. Spontaneous Forced Spontaneous Forced 1 0.05 1.25 0.81 0.85 0.00 1.69 0.00 0.97 0.47 0.53 0.01 0.59 Calculate the Amott-Harvey wettability index for each core and explain the wetting characteristics of each core.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter7: Permeability

Section: Chapter Questions

Problem 7.22P: Refer to Figure 7.24. The following data were collected during the field permeability measurement of...

See similar textbooks

Similar questions

Plot the following data and determine the preconsolidation pressure and the modified compression index. % Consolidation (Compression is +) Pressure (kPa) % Consolidation (Compression is +) Pressure (kPa) 0.09 5 7.34 160 0.11 10 7.6 320 0.12 20 8.35 640 0.26 40 12.65 1280 0.98 80 17.41 2560 1.91 160 22.18 5120 4.19 320 21.65 1280 8.05 640 20.63 160 8.03 320 19.26 40 7.83 160 15.35 5 7.21 80 Specimen height is 2.54MM, Sample is from a depth of -11.5m
Refer to Figure 7.24. The following data were collected during the field permeability measurement of a confined aquifer using a pumping test. Determine the hydraulic conductivity of the permeable layer. Use Eq. (7.49). Thickness of the aquifer, H = 4.5 m Piezometric level and radial distance of the first observation well: h1 = 2.9 m; r1 = 17.8 m Piezometric level and radial distance of the second observation well: h2 = 1.8 m; r2 = 8.1 m Rate of discharge from pumping, q = 0.5 m3/min
Please solve fastly You are an oil and gas exploration reservoir engineer and your manger asked you to calculate the porosity for the following reservoir. Seismic data have been used to delineate reservoir structure (The length of this reservoir is about 200 meter, thickness is 1 meter and width is 0.8 km). A- Calculate the bulk volume of the reservoir in m3 . Make sure all the unit is consistent with each other. B- Assume that the pore spaces of the sediment in the oil-bearing unit are full of oil 32000m3. Calculate the porosity of the reservoir. C- Based on the porosity value. Is this negligible, poor, fair , or very good reservoir ( try to find table for reservoir classification based on porosity value)
Q: I an oedometer test on a specimen of saturated clay (Gs = 2.72), the applied pressure was increased from 107 1o 214 kPa and the following compression readings recorded: TaBLE| Tmen 0 025 05 1 225 4 &5 9 16 Guugelmm) 78 742 732 721 6% 678 &6 643 637 Teme(mi) 25 % 4 s om0 X0 a0 Guge(nm) 629 626 621 618 616 615 610 602 After 1440 min, the thickness of the specimen was 15.30 mm and the water content was 23.2%. Determine the values of the coefficient of consolidation and the compression atios from (a) the root time plot and (b) the log time plot. Determine also the values of the coefTicient of volume compressibility and the coefficient of permeability.
Q1) B) using the Bingham plastic model determine the pressure losses in the annulus for the following well: (4 Marks) Data Length of drill pipe= 9000 ft Drill pipe = OD/ID = 5 in /4.276 in Hole diameter = 8.5 in |Page Plastic viscosity = 25 cp Yield point = 20 Ibf/100ft2 Flow rate = 300 gpm Mud density = 10 ppg %3D
Sample 2: Mass with empty mold M1 Mass of soil and mold M2 Hydraulic Head h Time interval t Volume V 145 g 250 g 950 mm 0.34 min 0.0046 L 145 g 260 g 900 mm 0.33 min 0.0049 L 145 g 228 g 922 mm 0.30 min 0.0051 L 145 g 281 g 915 mm 0.29 min 0.0044 L 145 g 219 g 908 mm 0.39 min 0.0042 L The diameter of the mold = 2.5 cm, Length of the sample = 0.3 m can u pls Find the permeability coefficient Mass of the soil Bulk Density Dry Density thank you Void Ratio
Data for Triaxial Test: Initial Length = Lo = 83mm. Initial Diameter = Do = 38mm. Cell Pressure = õ3 =128 kpa Deformation (AL) (mm) 0.1 0.3 Load (N) 30.97 0.6 1 61.94 89.65 118.9 1.2 128.77 1.4 140.18 1.5 146.7 1.6 148.33 1.7 144.71 1.8 143.44 1- Find the maximum shear stress that will be resisted by soil before failure? 2- Find the soil strength parameters (C, 0)? 3- Draw Mohr circle.
Question 3 a. An oil well in the Nameless Field is producing at a stabilized rate of 600 STB/day at a stabilized bottom-hole flowing pressure of 1800 psi. Analysis of the pressure buildup test data indicates that the pay zone is characterized by a permeability of 120 md and a uniform thickness of 25 ft. The well drains an area of approximately 40 acres. The following additional data is available: w = 0.25 ft, A = 40 acres Bo = 1. 25 bbl/STB, Ho = 2. 5 cp Calculate the pressure profile (distribution) and list the pressure drop across 1 ft intervals from rw to 1.25 ft, 4 to 5 ft, 19 to 20 ft, 99 to 100 ft, and 744 to 745 ft.
A sample of sand, 5 cm in diameter and 15 cm long, was prepared at a porosity of 60% in a constant-head apparatus. The total head was kept constant at 30 cm and the amount of water collected in 5 seconds was 40 cm^3. The test temperature was 20 deg C. Calculate the hydraulic conductivity. Provide a diagram a.5.0 x 10^-2 b.3.47 x 10^-2 c.2.0 x 10^-1 d.6.7 x 10^-1
1. During Atterberg limit tests in the soil mechanics laboratory, the students obtained the following results from a clayey soil. Liquid limit tests: Number of Moisture blows, N content (%) 14 38.4 16 36.5 20 33.1 28 270 Plastic limit tests: Students conducted two trials and found that PL = 172% for the first trial and PL = 17.8% for the second trial. a. Draw the flow curve and obtain the liquid limit. b. What is the plasticity index of the soil? Use an average value of PL from the two plastic limit trails.
AVA araupp g A p u s A pup upp n. 1. Answer the following questions about porosity and permeability: a) Name three (3) parameters which are involved in calculation of porosity. b) Name four geological mechanisms affecting porosity values. c) Describe effect of sorting on porosity. d) Describe how porosity and permeability are associated with one another. e) Permeability is seldom uniform throughout a reservoir. Thus, it is necessary to ascertain an average value of permeability, kavg. Elaborate with suitable diagrams two (2) examples of permeability averaging techniques. f) Two sandstone reservoir formations designated A and B are located 1 km apart. Their properties are given in Table Q1(f). Outline FOUR (4) reasons for which reservoir B is commercially more viable than reservoir A.
i. A sandstone core sample is saturated 100% with water. Calculate the absolute permeability of the core sample if the water is flowing at 6.21 cubic centimetres per second. The length of the core sample is 14 centimetres and its diameters is 6 centimetres. The pressure differential across the core sample is 15 atmospheric pressure and the water viscosity is 1.2 centipoises. Explain a method of how the permeability of low permeability reservoirs can be ii. improved.