00 1/1 1/1 0/1 1/0 0/0 11 01 0/1 a) Complete the Next State and Output columns of the State Table b) Using the Excitation Table of the JK Flip-Flop, determine the inputs for the two Flip-Flops (Ja, KA and JB, Kß) for each state transition c) Use Karnaugh Maps to minimize the functions of the combinational circuit for each Flip-Flop input (JA, KA and JB, KB) as well as the combinational circuit for the output (Y)

00 1/1 1/1 0/1 1/0 0/0 11 01 0/1 a) Complete the Next State and Output columns of the State Table b) Using the Excitation Table of the JK Flip-Flop, determine the inputs for the two Flip-Flops (Ja, KA and JB, Kß) for each state transition c) Use Karnaugh Maps to minimize the functions of the combinational circuit for each Flip-Flop input (JA, KA and JB, KB) as well as the combinational circuit for the output (Y)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design a Up Down Counter by using JK flip flop and verify the output of your designed circuit onany random input. Provide the following information as well:1. State table2. State diagram3. State equations4. Complete circuit diagram
Question: The flip-flops in the drawing below are positive edge triggered D flip-flops. Let Q2, Q1, QO = 0,0,0 initially. a) Plot the clock, Q2, Q1 and QO until the outputs begin to repeat. b) Show the circuits acts as a counter 00 1000 Hz/50%
A description of the principles of operation of the following sequential logic devices: J-K flip-flop Within the report, you need to provide the combinational logic equivalent circuit of every device, the function (truth) table and a timing diagram for the input, clock and output digital waveforms.
5. JK flip-flops are often used to build counters. The JK flip-flop will toggle the original output value when triggered by the clock signal if both the J,K inputs are connected with a constant "high"(logic 1). All the JK flip-flops in Figure 2 are negative edge triggered. All the initial values of Q2Q1Q0 are 0. Qo (LSB) (MSB) Input K K Logic 1 Input Q2 000 Figure 2. Counter (a) Sketch the output waveforms forQ2 Q1 Q0. Write down the output binary value (Q2Q1Q0: such as "000", "001") for each clock period on the figure. (b) Describe the function of the counter (e.g. binary down counter counting from 7 to 0).
A description of the principles of operation of the following sequential logic devices: D-type flip-flop Within the report, you need to provide the combinational logic equivalent circuit of every device, the function (truth) table and a timing diagram for the input, clock and output digital waveforms.
Which of the following statements is true regarding a D flip flop? O a. All changes on D will be observed at Q. O b. Q will be equal to D after the clock transition. O c. Q is equal to D all the time. O d. Q is equal to D as long as the clock is high.
show the waveforms for each flip-flop output with respect For the ring counter in Figure to the clock. Assume that FF0 is initially SET and that the rest are RESET. Show at least ten clock pulses. D D. FFO FF1 FF2 FF3 FF4 FF5 FF6 FF7 FF8 FP9 CLK
Convert a single J-K flip flop to a T-flip flop. Include all steps involved. What is the next count if the counter started with 000 and 011 (unused states)? i want the anwer for the second qustion
In the below diagram, all the D flip flops are positive edge triggered. For each flip flop there is no direct connection between D and Q, but Q is directly connected to D. Initially clock signal is zero and Qo, Q1, Q2 and Q3 are zero as well. What are the values of Q0, Q1, Q2, and Q3 after exactly 12 positive edges of the clock signal? Explain your answer. Clock D Qo Q1 D Q2 D Q3
010 For the state diagram shown below. what is the Boolean expression of the flip-flop inputs if you assume that the circuit is built using T flip-flops. (Assume that the binary code is assigned in an ascending order for the states starting from state A). X is the external input.
Write the next-state equations for the flip-flops and the output equation. (b) Construct the transition and output tables. (c) Construct the transition graph. (d) Give a one-sentence description of when the circuit produces an output of 1. Q2 D2 Q1 T1 CLK Figure 4
16. The following serial data are applied to the flip-flop through the AND gates as indicated in Figure 7-85 Ⓒ. Determine the resulting serial data that appear on the Qoutput. There is one clock pulse for each bit time. Assume that Q is initially 0 and that and PRE are HIGH. Rightmost bits are applied first. J₁: 1010011; J₂:0111010; J: 1111000; K: 0001110; K 1101100, K: 1010101 CLK K₁ CLR Figure 7-85 C K PRE -Q CLR